Home | Ezine | Forums | Links | Contact
NitroExpress.com: Follow Up on my hand loading issues

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies


*** Enjoy NitroExpress.com? Participate and join in. ***

Shooting & Reloading - Mausers, Big Bores and others >> Mannlicher Discussion forum & Archive

DonZ
.300 member


Reged: 24/12/12
Posts: 122
Loc: BW
Re: Follow Up on my hand loading issues
      17/07/16 12:54 PM

I did want to follow up on this one as well. Last week, I sent an email to VV to ask their opinion, but as of yet have not heard back.

I went down to 35 grains and was still massively over-pressured. Headspace seems tight without being too tight (.004 inches or so), and was certainly not excessive. I have a case gauge on the way, and will go to full length sizing instead of neck sizing. I have fired off all of my primed cases, so am at zero. I have about 40 once fired RWS cases, and another 40 once fired Norma cases. The rest of my collection is RWS and Norma virgin cases, so they would need full length sizing to start.

At this point, the only thing to which I can place the blame is bad powder. I can think of no other change I could make (to include having the manufacturer recalibrate my balance scale). I was using Woodleigh PP bullets, but they were loaded to a COL of 3.009, which is well within max COL specs, and the meplat of that bullet would keep it farther from the lands than a simple round nose bullet. At this point, I will try and source another powder. Hogden and IMR are back on the shelves, so that is easy. I've also seen some Norma powder, and they have recommended loads on their site.

I'm hoping I haven't damaged the rifle by this. Certainly the cases did not rupture (though the bolt was extremely difficult to open) so I probably have not exceeded the proof load originally performed in late 1939.

Thanks everyone for all your advice, recommendations and patience. The only way I can use this to continue to be a threat to Odocoileus virginianus is to learn to reload, so I am trying to blunder my way through.

--------------------
Honor never grows old, and honor rejoices the heart of age...

Post Extras Print Post   Remind Me!     Notify Moderator


Entire topic
Subject Posted by Posted on
* Follow Up on my hand loading issues DonZ 28/06/16 12:54 PM
. * * Re: Follow Up on my hand loading issues Jim_C   28/06/16 02:06 PM
. * * Re: Follow Up on my hand loading issues DarylS   29/06/16 01:16 AM
. * * Re: Follow Up on my hand loading issues DarylS   07/07/16 01:18 AM
. * * Re: Follow Up on my hand loading issues DonZ   07/07/16 10:24 AM
. * * Re: Follow Up on my hand loading issues deeangeo   07/07/16 03:21 PM
. * * Re: Follow Up on my hand loading issues DonZ   17/07/16 12:54 PM
. * * Re: Follow Up on my hand loading issues DarylS   18/07/16 01:30 AM
. * * Re: Follow Up on my hand loading issues Tom_H   14/08/16 02:05 PM
. * * Re: Follow Up on my hand loading issues DonZ   15/08/16 01:17 PM
. * * Re: Follow Up on my hand loading issues Tom_H   16/08/16 08:37 AM
. * * Re: Follow Up on my hand loading issues DarylS   16/08/16 10:14 AM
. * * Re: Follow Up on my hand loading issues DonZ   16/08/16 11:17 PM
. * * Re: Follow Up on my hand loading issues ducmarc   17/08/16 10:55 AM
. * * Re: Follow Up on my hand loading issues ducmarc   17/08/16 11:05 AM
. * * Re: Follow Up on my hand loading issues Postman   17/08/16 11:27 AM
. * * Re: Follow Up on my hand loading issues DarylS   17/07/16 02:42 PM
. * * Re: Follow Up on my hand loading issues TexasJohn   17/07/16 09:58 PM
. * * Re: Follow Up on my hand loading issues DonZ   17/07/16 10:28 PM
. * * Re: Follow Up on my hand loading issues DonZ   06/07/16 12:42 PM
. * * Re: Follow Up on my hand loading issues deeangeo   06/07/16 04:45 PM

Extra information
1 registered and 57 anonymous users are browsing this forum.

Moderator:  CptCurl 



Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 3843

Rate this thread

Jump to

Contact Us NitroExpress.com

Powered by UBB.threads™ 6.5.5


Home | Ezine | Forums | Links | Contact


Copyright 2003 to 2011 - all rights reserved