Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: My Model 46 Husqvarna in 9.3 X 57

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Shooting & Reloading - Mausers, Big Bores and others >> Mauser Discussion Forum

sharps4590
.333 member

Reged: 09/03/16
Posts: 250
Loc: Missouri Ozarks

Re: My Model 46 Husqvarna in 9.3 X 57
30/04/16 02:14 AM

Took the opportunity to shoot across the screens this morning while I still could. Thunderstoms arriving in about an hour.

Velocity with 40 grs. of IMR-4895 was not as high as I expected....by quite a bit. It averaged barely over 1800 fps. I ended up at 44 grains in one grain increments, skipping 41 grs., to get an average of 1971 fps. Accuracy held good throughout, better than I expected after the 41 gr. performance.

Then I broke out the IMR-4064. I suspected it would shoot as accurately as the 4895 but got a surprise. A 9 round composite group was less than 1 inch at 50 yards with three different powder charges of 43, 44 and 45 grs. Surprisingly to me the velocity with 45 grs. averaged identical to the 4895 final load, 1971 fps. Pressure signs were fine throughout, which I imagine most of you suspect. I didn't make any head expansion comparisons but bolt lift, extraction and primer condition make one thing there's room for more 4895. With the cases I'm using there's only room for about 1 more grain of IMR-4064 before having a compressed load. With both powders the rifle would shoot the first two very, very close and nearly in the same hole with 4064, then put the third round slightly out of the group. Not much but it was evident and amazingly consistent which is why I'm not blaming me....yet. I suspect the recoil lug and/or the screw that goes through the bottom, middle of the forearm and into a boss on the barrel. I haven't done any of the things Iowa_303 told me to do but they are on the list for next.

From the data I've seen and what Iowa sent me it appears this rifle has a slow barrel or perhaps differences in powder lots...or something I'm ignorant of.

I also put my little Jeffrey Rook in 25-10 across the screens while I had them set up. Laughable is the word that comes to mind. 112 fps difference from hi to low with a load of 9 grs. of IMR-4227 and a 75 gr. bullet. The 9.3 shot the pants off the Rook but there's a world of difference in bore condition.

--------------------
Jesus said, "I am the way the truth and the life. No one comes to the Father but through me." John14:6

Post Extras

Print Post

Remind Me!

Notify Moderator

Entire topic
Subject	Posted by	Posted on
My Model 46 Husqvarna in 9.3 X 57	sharps4590	21/04/16 12:48 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	21/04/16 12:56 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	21/04/16 01:55 AM
Re: My Model 46 Husqvarna in 9.3 X 57	Iowa_303s	21/04/16 09:17 AM
Re: My Model 46 Husqvarna in 9.3 X 57	Homer	21/04/16 06:46 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	21/04/16 09:50 PM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	22/04/16 01:36 AM
Re: My Model 46 Husqvarna in 9.3 X 57	D_the_D	22/04/16 03:25 AM
Re: My Model 46 Husqvarna in 9.3 X 57	Iowa_303s	22/04/16 03:36 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	22/04/16 06:54 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	23/04/16 02:22 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	23/04/16 07:01 AM
Re: My Model 46 Husqvarna in 9.3 X 57	lancaster	24/04/16 08:21 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	28/04/16 03:15 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	28/04/16 12:43 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	28/04/16 09:36 PM
Re: My Model 46 Husqvarna in 9.3 X 57	lonewulf	28/04/16 11:56 PM
Re: My Model 46 Husqvarna in 9.3 X 57	D_the_D	29/04/16 07:36 AM
Re: My Model 46 Husqvarna in 9.3 X 57	Igorrock	29/04/16 12:53 PM
Re: My Model 46 Husqvarna in 9.3 X 57	D_the_D	29/04/16 01:02 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	29/04/16 08:21 PM
Re: My Model 46 Husqvarna in 9.3 X 57	Igorrock	29/04/16 11:13 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	30/04/16 02:14 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	30/04/16 02:26 AM
Re: My Model 46 Husqvarna in 9.3 X 57	Wanabebwana	08/06/16 10:21 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	10/06/16 09:58 PM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	11/06/16 12:43 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	11/06/16 06:13 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	11/06/16 08:26 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	11/06/16 07:37 PM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	12/06/16 02:15 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	12/06/16 09:42 PM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	13/06/16 12:23 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	19/06/16 09:29 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	30/04/16 02:46 AM
Re: My Model 46 Husqvarna in 9.3 X 57	D_the_D	30/04/16 05:19 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	30/04/16 06:41 AM
Re: My Model 46 Husqvarna in 9.3 X 57	D_the_D	30/04/16 10:19 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	30/04/16 10:55 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	30/04/16 02:04 PM
Re: My Model 46 Husqvarna in 9.3 X 57	D_the_D	30/04/16 03:52 PM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	30/04/16 09:47 PM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	01/05/16 12:24 AM
Re: My Model 46 Husqvarna in 9.3 X 57	sharps4590	01/05/16 02:16 AM
Re: My Model 46 Husqvarna in 9.3 X 57	DarylS	29/04/16 12:31 AM

Extra information

0 registered and 94 anonymous users are browsing this forum.

Moderator: NitroX

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 15160

Jump to

NitroExpress.com

Powered by UBB.threads™ 6.5.5

Home | Ezine | Forums | Links | Contact

Copyright 2003 to 2011 - all rights reserved