Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: Forming cases for 6.5x53R

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Shooting & Reloading - Mausers, Big Bores and others >> Mannlicher Discussion forum & Archive

2152hq
.300 member

Reged: 20/05/12
Posts: 126
Loc: USA

Re: Forming cases for 6.5x53R
10/10/13 12:21 PM

I use a 308 or 300Sav die to sometimes push the shoulder back first,,but not always.
I find it's needed more on 303 HXP military brass that I use a lot rather than the 30 Krag brass I use occasionally. Heavier constructed I guess.

Otherwise lube it up well especially at the base. Avoid too much lube around the neck or you'll get dents in the reformed neck. One push into the 6.5 die and there's your case but with some trimming to do of course.
An intermediate step into a 7mm die or something else close to that is a good idea but I've been lucky not having any problems sidestepping it (so far).
Some brass may buckle w/o doing that though.

I use 6.5 Mannlicher Schoenauer dies.
The 303 HXP I have to reduce the base a few .000" before they'll chamber. Not needed on the Krag brass (Remington). But I'd rather keep the Krag brass for the Krag as it's getting harder to get now.
The HXP needs an inside neck ream to remove a 'step' inside at the bottom of the neck from the forming process. No reamer available, so I used and continue to use a 'G' drill (IIRC that's the one I keep in the box). It's about .262d and cleans everything up OK.
Once they are 'drilled', I run them through the FL sizer again only this time with the expander plug in place and the necks are ready for a bullet to be seated.
Never had a problem.

No rim turning but I've read where some have had to do that so they'd work OK in their rifle.

220 Swift can also be used if your rifle will work with the smaller dia rim on that case.
The 220 case has 30-06 size rim, the body is about right for the 6.5. Not much trimming after reforming and no neck turning to be done.
Can be used to make 6.5 M/S too but you have to turn the rim down of course and cut the extractor groove out a bit.

Post Extras

Print Post

Remind Me!

Notify Moderator

Entire topic
Subject	Posted by	Posted on
Forming cases for 6.5x53R	Spud303	08/10/13 07:42 PM
Re: Forming cases for 6.5x53R	Carpetsahib	09/10/13 02:11 AM
Re: Forming cases for 6.5x53R	kuduae	09/10/13 08:07 AM
Re: Forming cases for 6.5x53R	Claydog	09/10/13 09:01 AM
Re: Forming cases for 6.5x53R	Spud303	09/10/13 01:34 PM
Re: Forming cases for 6.5x53R	Claydog	09/10/13 01:41 PM
Re: Forming cases for 6.5x53R	Igorrock	09/10/13 06:58 PM
Re: Forming cases for 6.5x53R	Claydog	09/10/13 10:28 PM
Re: Forming cases for 6.5x53R	2152hq	10/10/13 12:21 PM
Re: Forming cases for 6.5x53R	Huvius	10/10/13 02:03 PM
Re: Forming cases for 6.5x53R	kuduae	13/10/13 06:44 AM
Re: Forming cases for 6.5x53R	lancaster	13/10/13 10:56 PM
Re: Forming cases for 6.5x53R	kuduae	14/10/13 03:23 AM
Re: Forming cases for 6.5x53R	Huvius	13/10/13 07:43 AM
Re: Forming cases for 6.5x53R	kuduae	13/10/13 08:56 AM
Re: Forming cases for 6.5x53R	Huvius	14/10/13 02:53 AM
Re: Forming cases for 6.5x53R	kuduae	14/10/13 03:38 AM
Re: Forming cases for 6.5x53R	Claydog	14/10/13 01:29 PM
Re: Forming cases for 6.5x53R	Spud303	14/10/13 06:26 PM
Re: Forming cases for 6.5x53R	Ireload2	17/12/13 11:56 AM
Re: Forming cases for 6.5x53R	tinker	17/12/13 02:59 PM
Re: Forming cases for 6.5x53R	2152hq	17/12/13 03:50 PM
Re: Forming cases for 6.5x53R	FrankS	22/12/13 10:54 PM
Re: Forming cases for 6.5x53R	Sarg	24/12/13 09:49 PM
Re: Forming cases for 6.5x53R	DarylS	25/12/13 03:48 AM
Re: Forming cases for 6.5x53R	Sarg	25/12/13 02:27 PM
Re: Forming cases for 6.5x53R	sparks1	23/12/13 05:10 AM
Re: Forming cases for 6.5x53R	2152hq	23/12/13 02:53 PM
Re: Forming cases for 6.5x53R	DarylS	18/12/13 04:28 AM
Re: Forming cases for 6.5x53R	Ireload2	20/12/13 06:06 AM
Re: Forming cases for 6.5x53R	tinker	20/12/13 10:15 AM
Re: Forming cases for 6.5x53R	2152hq	22/12/13 09:12 AM
Re: Forming cases for 6.5x53R	Igorrock	08/10/13 08:16 PM
Re: Forming cases for 6.5x53R	Spud303	08/10/13 08:32 PM
Re: Forming cases for 6.5x53R	HuntingSchneider	08/10/13 11:11 PM

Extra information

0 registered and 123 anonymous users are browsing this forum.

Moderator: CptCurl

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 21039

Jump to

NitroExpress.com

Powered by UBB.threads™ 6.5.5

Home | Ezine | Forums | Links | Contact

Copyright 2003 to 2011 - all rights reserved