Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: 1903 groove diameter

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Shooting & Reloading - Mausers, Big Bores and others >> Mannlicher Discussion forum & Archive

clatrans
.224 member

Reged: 21/07/12
Posts: 7
Loc: Texas

Re: 1903 groove diameter
28/07/12 12:46 AM

On Wednesday afternoon I had a little time and went out and shot three rounds loaded with 35 grains IMR 4350 and three rounds loaded with 37 grains H4831, both using the 156 gr. Lapua Mega soft nose, Federal 210 Match primers, at an OAL of 3.005, not crimped.
Velocities with the 4350 load were 1969, 1983 and 1934. The H4831 loads were 1881, 1852 and 1866.
I measured the base diameter of the cartridges before firing, new Norma cases, by putting the edge of the micrometer spindle (?) at the top of the extractor groove, so the measuring point was one half of the diameter of a Starret mic spindle up from the extractor groove.
In all cases the primers were pushed back by firing by an easily visible amount which I have not measured yet....more or less 20 to 50 thou.
The before and after head measurements for the 4350 loads were: .4430 and .4497, .4433 and .4497 and .4432 and .4494. I did not measure the 4831 loads but assume they would have been similar.
Opening the bolt and the extraction process was easy and smooth...no resistance. Accuracy at 100 yards was about 7 inches for the 4350 loads (very old powder but still smells OK) and about 3 inches for the H4831 loads.
About .006 case head expansion and way too much headspace makes me wonder if re-barreling is not the best course to follow.
As a 6.5x55 was mentioned above I looked up the head diameter of a 6.5x55 and found it to be .4803 on the 6mmBR website.
I would be very interested in your thoughts on this.

Post Extras

Print Post

Remind Me!

Notify Moderator

Entire topic
Subject	Posted by	Posted on
1903 groove diameter	clatrans	21/07/12 06:05 AM
Re: 1903 groove diameter	Kiwi_bloke	21/07/12 10:42 AM
Re: 1903 groove diameter	DarylS	21/07/12 11:04 AM
Re: 1903 groove diameter	MikeRowe	21/07/12 01:05 PM
Re: 1903 groove diameter	Paul	21/07/12 05:45 PM
Re: 1903 groove diameter	DarylS	22/07/12 01:41 AM
Re: 1903 groove diameter	clatrans	24/07/12 05:28 AM
Re: 1903 groove diameter	MikeRowe	25/07/12 03:14 AM
Re: 1903 groove diameter	clatrans	25/07/12 05:22 AM
Re: 1903 groove diameter	DarylS	25/07/12 06:35 AM
Re: 1903 groove diameter	clatrans	25/07/12 07:05 AM
Re: 1903 groove diameter	DarylS	25/07/12 10:56 AM
Re: 1903 groove diameter	Paul	25/07/12 01:48 PM
Re: 1903 groove diameter	DarylS	25/07/12 11:49 PM
Re: 1903 groove diameter	Paul	27/07/12 10:16 PM
Re: 1903 groove diameter	DarylS	27/07/12 11:50 PM
Re: 1903 groove diameter	Paul	28/07/12 01:57 PM
Re: 1903 groove diameter	DarylS	29/07/12 02:08 AM
Re: 1903 groove diameter	Paul	29/07/12 11:24 AM
Re: 1903 groove diameter	clatrans	28/07/12 12:46 AM
Re: 1903 groove diameter	DarylS	28/07/12 09:32 AM
Re: 1903 groove diameter	malco	22/07/12 12:40 AM

Extra information

0 registered and 32 anonymous users are browsing this forum.

Moderator: CptCurl

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 10562

Jump to

NitroExpress.com

Powered by UBB.threads™ 6.5.5

Home | Ezine | Forums | Links | Contact

Copyright 2003 to 2011 - all rights reserved