Home | Ezine | Forums | Links | Contact
NitroExpress.com: Some Info on ball mould size in 12 & 8 Bore ?

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies


*** Enjoy NitroExpress.com? Participate and join in. ***

Double Rifles, Single Shots & Combinations >> Paradox and Bore Guns

CommandCar
.333 member


Reged: 18/09/10
Posts: 292
Loc: East Coast, USA
Re: Some Info on ball mould size in 12 & 8 Bore ?
      20/12/11 02:23 PM

Sarg,

If your impacts are above the (original) sights POA and apart (right barrel shooting right, left shooting left), In general, with a bore rifle, you need to slow things down a bit or go to lighter slugs. You are getting too much recoil assuming you are holding the rifle correctly. There is tons of convergence built into bore rifles, especially the 8 & ups, so they behave slightly differently from the nitros. You probabally know this, but thought I'd throw it out there.

How was accuracy as you worked up from lower velocities?

Again, I urge you to spend most of your time at 100 yards, that is the first sight and you will learn the most.

Post Extras Print Post   Remind Me!     Notify Moderator


Entire topic
Subject Posted by Posted on
* Some Info on ball mould size in 12 & 8 Bore ? Sarg 13/12/11 10:58 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? gatsby   17/12/11 03:44 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? gatsby   17/12/11 03:40 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   17/12/11 02:06 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? Sarg   17/12/11 11:54 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   18/12/11 03:31 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? Sarg   18/12/11 07:13 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? tinkerModerator   19/12/11 01:49 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? Sarg   19/12/11 05:44 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   21/12/11 04:53 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? DarylS   21/12/11 05:03 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? DarylS   21/12/11 05:29 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? Sarg   21/12/11 12:11 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   21/12/11 12:57 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? rigbymauser   17/06/12 06:06 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   21/06/12 08:19 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? rigbymauser   22/06/12 06:25 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? DarylS   22/06/12 01:24 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? DarylS   18/06/12 02:08 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? tinkerModerator   18/06/12 02:05 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   20/12/11 02:23 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? tinkerModerator   20/12/11 02:51 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? gatsby   19/12/11 01:58 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? DarylS   19/12/11 03:53 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? gatsby   18/12/11 04:08 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? CommandCar   18/12/11 04:50 AM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? Sarg   18/12/11 12:32 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? gatsby   18/12/11 01:34 PM
. * * Re: Some Info on ball mould size in 12 & 8 Bore ? DarylS   18/12/11 04:58 AM

Extra information
0 registered and 7 anonymous users are browsing this forum.

Moderator:  tinker 



Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 12786

Rate this thread

Jump to

Contact Us NitroExpress.com

Powered by UBB.threads™ 6.5.5


Home | Ezine | Forums | Links | Contact


Copyright 2003 to 2011 - all rights reserved