Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: Saturday's casting session

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Shooting & Reloading - Mausers, Big Bores and others >> Cast Bullets

450_Ackley
.375 member

Reged: 06/02/03
Posts: 583
Loc: Darling Downs, Qld Australia

Re: Saturday's casting session
26/04/11 07:36 AM

Neale, you could... but, measuring the precise amount of softer lead for the tip is a nightmare, and then having it harden too much before you pour the base. It has all been done before.
You can still buy moulds that cast the tip part first, by itself, then after they harden, you can place it in the full mould cavity, then pour the base section, or you can cast both parts seperately and epoxy them together, the weakest part will always be the join however, they come apart there when they hit something.
Also hard and soft alloys vary in dimension, even when cast from the same mould, and getting the two parts to fit correctly is nearly impossible.
Best to make a slightly softer bullet, load it so it doesn't lead, and hope for the best results possible.
Hollow points don't open up as readily as jacketed hollow points, at the speeds we would be driving cast bullets.

Even read a story in an old magazine last night about wire wound cast bullets, where the caster wound up copper coils from wire, placed them in a specially made mould, poured the core and had himself a semi-jacketed bullet, no leading and softer core lead. The downside is that he could only make 17 per hour!

Regards,
David.

Post Extras

Print Post

Remind Me!

Notify Moderator

Entire topic
Subject	Posted by	Posted on
Saturday's casting session	450_Ackley	24/04/11 09:29 AM
Re: Saturday's casting session	FATBOY404	24/04/11 12:03 PM
Re: Saturday's casting session	450_Ackley	24/04/11 05:50 PM
Re: Saturday's casting session	Perry	25/04/11 11:24 PM
Re: Saturday's casting session	DarylS	26/04/11 02:55 AM
Re: Saturday's casting session	FATBOY404	26/04/11 06:59 AM
Re: Saturday's casting session	450_Ackley	26/04/11 07:36 AM
Re: Saturday's casting session	FATBOY404	26/04/11 07:15 PM
Re: Saturday's casting session	Sarg	26/04/11 07:37 PM
Re: Saturday's casting session	DarylS	27/04/11 02:07 AM
Re: Saturday's casting session	eagle27	27/04/11 05:03 PM
Re: Saturday's casting session	450_Ackley	27/04/11 07:57 PM
Re: Saturday's casting session	FATBOY404	27/04/11 08:10 PM
Re: Saturday's casting session	450_Ackley	27/04/11 08:42 PM
Re: Saturday's casting session	450_Ackley	26/04/11 06:56 AM

Extra information

0 registered and 64 anonymous users are browsing this forum.

Moderator: DarylS

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 6935

Jump to

NitroExpress.com

Powered by UBB.threads™ 6.5.5

Home | Ezine | Forums | Links | Contact

Copyright 2003 to 2011 - all rights reserved