casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
I've found brass and dies for my model 1905. Bore slugs at .352, tight. I can't seem to find any .355 200 grain round nose bullets in google search. they are mostly .358. Anyone know of any .355 or .356 200 grain round nose bullets? Thanks.
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27682
Loc: Beautiful British Columbia, Ca...
|
|
Only thing I can suggest is Lee sizer dies, each one .002 to 3" smaller than the other, to get down to groove diameter.
So - .356", then .354", and likely .352".
This is what I would do.
--------------------
Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
3DogMike
.400 member
Reged: 29/01/15
Posts: 1487
Loc: Western Slope, Colorado USA
|
|
Quote:
I've found brass and dies for my model 1905. Bore slugs at .352, tight. I can't seem to find any .355 200 grain round nose bullets in google search. they are mostly .358. Anyone know of any .355 or .356 200 grain round nose bullets? Thanks.
Try Hawk bullets. https://hawkbullets.com/bullet-selection.html
They offer 200 grain for .351” for the .351 Win Self Loader as well as .353”, .354”, .356” for 9mm rifles.
He can be hard to get ahold of sometimes but in the end it is worth it with obscure bullet sizes and weights.
They are much like the old Barnes copper jacket cup and core bullets, I personally find they work just fine at “vintage rifle” velocities.
- Mike
--------------------
"Will Rogers never met a fighter pilot"
- Anon
“Always carry a flask of whiskey in case of snakebite, and furthermore always carry a small snake."
-- W. C. Fields
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
I called Hawk 3dog. Backorder but said would be run this summer. Guess I take what I can get. Thanks.
|
3DogMike
.400 member
Reged: 29/01/15
Posts: 1487
Loc: Western Slope, Colorado USA
|
|
Quote:
I called Hawk 3dog. Backorder but said would be run this summer. Guess I take what I can get. Thanks.
I guess in this economy and state of things that’s doing well….. 
- Mike
ADDED:
Too bad that, thanks to ITAR, it is just too hard for we in the USA to import reloading components from Europe. I would guess that there would be proper size 9mm rifle components fairly easily available somewhere in the EU?
--------------------
"Will Rogers never met a fighter pilot"
- Anon
“Always carry a flask of whiskey in case of snakebite, and furthermore always carry a small snake."
-- W. C. Fields
|
fjrdoc
.333 member
Reged: 20/05/22
Posts: 251
Loc: United States
|
|
I just purchase a 1905 M-S and I slugged the barrel. I contacted Hawk Bullets and I placed an order for .354 RN from them. They told me the same thing ..... should be available early summer.
I have been considering purchasing this for reloading of this rifle.
http://swinglock.net/
I purchased one for drawing down .323 bullets for my .318 8mm J Simpson Suhl hunting rifle. The die is adjustable which helps if you experience "spring back" after sizing. They aren't exactly cheap but the ability to adjust the diameter saves on buying multiple dies. It also gives you a chance to experement with various bullet diameters.
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
I'm not going to shoot it enough to justify $175 on a sizing die.
|
93x64mm
.416 member
Reged: 07/12/11
Posts: 4401
Loc: Nth QLD Australia
|
|
Never heard of an 'adjustable' sizing die before!
I'm sure it'll work for your MS as well Fjrdoc.
Well done indeed
|
fjrdoc
.333 member
Reged: 20/05/22
Posts: 251
Loc: United States
|
|
I was very impressed with the quality of the product. It's nice to have variable options.
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27682
Loc: Beautiful British Columbia, Ca...
|
|
Adjustable bullet sizing die is news to me as well. Interesting and can't help but wonder how it's made.
--------------------
Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
szihn
.400 member
Reged: 24/06/07
Posts: 2121
Loc: United States
|
|
Slug your bore. I had an old M/S 9X65 and hunted with it a few years. The grooves mikes at .3585 instead of the .355" we are all told they have.
I used standard American .358" 35 cal bullet in it and that worked perfectly.
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
I stated in the first post here that the bore slugged at .352.
|
fjrdoc
.333 member
Reged: 20/05/22
Posts: 251
Loc: United States
|
|
I placed an order for 250 grain bullets for my 1905 MS through Hawk. I was told that they would probably be produced in early summer. I stumbled upon the Quality Cartridge home page:
http://www.qual-cart.com/
As I looked through their online catalog, I noticed that they offer 200 and 250 grain monolithic hunting bullets in.354 and .356 diameters. I spoke with Pete at QC and he suggested that I try the .354 diameter 200 grain bullets in my .355 barrel.
I'm anxious to do some shooting with my 1905 so I purchased a box. This is a spitzer design so I'll have to see how it functions in the rotary magazine. My 1903 handles Hornady 129 gr Interlock spire points without a problem.
I'll report back to the forum once I get a chance to give these bullets a try.
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
I'd be interested in knowing if they will work for sure. My bore slugs at .352 though.
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27682
Loc: Beautiful British Columbia, Ca...
|
|
Only if the oversized bullets will fit inside a fired case from your rifle.
According to Ackley, if the chamber's neck allows enough expansion to release the oversized bullets, there will be zero or very little increased pressures, according to his tests with shooting up to .35*" bullets from a .30/06. He had to increase the neck diameter of the chamber to allow the shooting of the 150gr. .358 bullets. The same powder charge was used for all bullet diameters tested.
--------------------
Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
fjrdoc did you slug your bore to determine the bore size?
|
fjrdoc
.333 member
Reged: 20/05/22
Posts: 251
Loc: United States
|
|
Yes, I slugged my barrel and it measured .355
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
I've heard that there are quite a few different size bores.
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27682
Loc: Beautiful British Columbia, Ca...
|
|
Can't help but wondering the chamber reamers used, were all similar or to CIP specs, in that they would allow the largest bullets be used, ie: .358/7?
Found this:
This would suggest if the fired case's neck is larger than .380", that it would hold/chamber a .357" bullet, no matter what the groove diameter was.
If this is the "case" then suitable reloading data could be produced.
If a fired case does not allow a bullet to enter, that diameter bullet cannot be used, unless other 'things' are done to the chamber, the case, or perhaps both.
--------------------
Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
They seem to run from the smallest like mine of .352 to .358. Quite a large range for bore diameter.
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27682
Loc: Beautiful British Columbia, Ca...
|
|
Seemingly, not much CIP compliance.
I have 2 boxes of 9MM Mauser Kynoch 245gr. ammo (19rounds). The bullets measure .355/6 at the case mouth.
--------------------
Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
3DogMike
.400 member
Reged: 29/01/15
Posts: 1487
Loc: Western Slope, Colorado USA
|
|
Quote:
Seemingly, not much CIP compliance.
I have 2 boxes of 9MM Mauser Kynoch 245gr. ammo (19rounds). The bullets measure .355/6 at the case mouth.
In that CIP was only enacted in 1969 dimensions would seem to have been open to gun and ammunition makers “interpretation” back when most of these rifles were made.
Keep in mind some original .404/10.75mm had .418” groove-groove barrels and .422”-.423” bullets.
The oversized bullets worked well enough and simply were squeezed to size in the throat. Soft(ish) jackets of cupronickel, mild steel, or gilding metal and cup & core bullets.
- Mike
--------------------
"Will Rogers never met a fighter pilot"
- Anon
“Always carry a flask of whiskey in case of snakebite, and furthermore always carry a small snake."
-- W. C. Fields
|
casper50
.400 member
Reged: 18/10/07
Posts: 1536
Loc: Alaska
|
|
Yes, but you'd think that a manufacturer would use the same measurement for a single model.
|
3DogMike
.400 member
Reged: 29/01/15
Posts: 1487
Loc: Western Slope, Colorado USA
|
|
Quote:
Yes, but you'd think that a manufacturer would use the same measurement for a single model.
Who knows?
Maybe a different barrel supplier? Barrel made on a Monday? Barrel made in the afternoon after a "3 pot" lunch? 
- Mike
--------------------
"Will Rogers never met a fighter pilot"
- Anon
“Always carry a flask of whiskey in case of snakebite, and furthermore always carry a small snake."
-- W. C. Fields
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27682
Loc: Beautiful British Columbia, Ca...
|
|
The same discrepancy happens in the 9.3x57's as to groove to groove dimensions as well as body length differences from the standard 57mm Mauser case. The body needed to fit my chamber was .019" longer than the 8mm Mauser body. With soft-ball loads in the 30,000PSI to 35,000PSI range, if brass was simply necked up 8x57, in many rifles the firing of low pressure loads resulted in backed out primers due to the longer body length in the chamber producing excessive headspace.
--------------------
Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
Previous
Index
Next
Threaded
Edit
Reply
Quote
