Home | Ezine | Forums | Links | Contact
NitroExpress.com: Pitted chambers - a possible solution ?

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies


*** Enjoy NitroExpress.com? Participate and join in. ***

Double Rifles, Single Shots & Combinations >> Building Double Rifles & Gunsmithing

Pages: 1 | 2 | >> (show all)
theprof1
.224 member


Reged: 01/02/19
Posts: 33
Loc: Queensland
Pitted chambers - a possible solution ?
      #330295 - 19/07/19 06:55 PM

Warning, this is a silly idea of mine so please feel free to call me a dangerous nutter.
Some years ago I had a .500 3" BP Jeffery double, the right barrel had a noticeable pit about half way down the chamber at about 2 o'clock viewed from the breech. I tolerated this for the life of the rifle while I was it's custodian. When a load seemed to get close to maximum the brass would acquire a small raised dimple at the pit location, I then backed off in my regulation loads. I have often wondered if a good clean of the pit, with Hydrochloric acid - which I used to use for stripping old barrel browning when it had gone beyond cleaning up and needed re browning.
My thought was a small deposit of dental amalgam ( mix of mercury, silver, tin and copper). This stuff is tough takes years of gnawing bones to break up fillings. I would be softer than the chamber steel so over filling could be honed / lapped out with little effect on the steel. It would be incompressible and hard. There may be more effective ways of rescuing a chamber in which extraction becomes difficult, but I have been out of gunsmithing for years. Amalgam doesnt seem very popular these days as there are many more painless dental filling materials these days, perhaps it may not even be used any more but some old near retired dentist may be persuaded to dust of his amalgamating equipment and try it on a pit?
All comments welcome.


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: theprof1]
      #330298 - 19/07/19 11:38 PM

It doesn't sound like a silly idea to me at all.
Sounds like it would work.

I don't know the specifics on the alloy for dental amalgam. It's time I look at the specifics.
The compression strength is in the range of 55,000 - 59,500 pounds-force per square inch
Interesting proposition!

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
theprof1
.224 member


Reged: 01/02/19
Posts: 33
Loc: Queensland
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330302 - 20/07/19 12:05 AM

Thank you for having the interest to reply. The main issue is adhesion of the amalgam to the parent steel. This would be overcome by a thorough cleaning of the pit. My procedure would be as follows : get a pack of brake clean, use the wife's hair dryer and carefully put a right angle bend on the tip of the tube, blast the pit - this will remove most of the grease, oil, crud, and powder/ smoke residue. I would do this twice as it evaporates quite quickly. Then you would use a fairly concentrated solution of caustic soda - Na Oh. Beware this shit requires full P.P.E - safety glasses and rubber gloves, one drop of Caustic in your eye will crater the surface of the eye ball.... This process of using caustic is called scouring the steel. Removes all built up oils, waxes and carbonaceous material. After using the caustic - 20 mins, flush with a full jug of boiling water, this will remove remaining caustic and heat the chambers so they dry out. The next step is to use a cotton bud soaked in strong hydrochloric acid, this will remove some or all rust remaining in the pitting - again flush well with boiling water. By now you will have 2 things, a clean pit and a chamber avid for oxygen, it will start to rust real quick, just with atmospheric oxygen. The steel will be naked and oxygen hungry. You need to perform the last step just before your trip to the dentist. Hopefully your dentist will allow for your slightly deranged request and book it down as a standard tooth filling so you can claim it on your health insurance. Best of luck lol.

Post Extras: Print Post   Remind Me!   Notify Moderator  
DarylS
.700 member


Reged: 10/08/05
Posts: 27000
Loc: Beautiful British Columbia, Ca...
Re: Pitted chambers - a possible solution ? [Re: theprof1]
      #330303 - 20/07/19 12:19 AM

VERY interesting topic. I am quite interested in the results of this experiment.

--------------------
Daryl


"a gun without hammers is like a Spaniel without ears" King George V


Post Extras: Print Post   Remind Me!   Notify Moderator  
theprof1
.224 member


Reged: 01/02/19
Posts: 33
Loc: Queensland
Re: Pitted chambers - a possible solution ? [Re: DarylS]
      #330304 - 20/07/19 12:26 AM

Sadly Tinker and Daryl, I am not any longer in possession of the 500, had to pass it on to to it's next custodian The thought was there, just hoping to give some hope to those with damaged chambers in their valuable guns. This is a small thought for the next generations, lucky enough to own a fine antique rifle.

Post Extras: Print Post   Remind Me!   Notify Moderator  
Vladymere
.300 member


Reged: 11/08/15
Posts: 187
Loc: North Carolina, USA
Re: Pitted chambers - a possible solution ? [Re: theprof1]
      #330318 - 20/07/19 07:53 AM

Currently my dentist uses an epoxy mixture, that is cured by a black light, for fillings. I wonder if a good epoxy might not work for filling pits in the chamber?

Vlad


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: Vladymere]
      #330320 - 20/07/19 08:02 AM

The fellows at the shop are interested.
I'll be getting some materials and going forward with this.

For shotgun, bore rifle, and BPE chambers - and many NE chambers, this should be a good solution.
I don't know why I hadn't ever thought of this.
I and many other guys I know have thought of the epoxy materials, but one way or the other we've all steered clear of the plastic fantastic.

I'll post back with whatever I learn.
I will be talking to my dentist too along the way.
I'm sure he'll have some good points to consider.

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
theprof1
.224 member


Reged: 01/02/19
Posts: 33
Loc: Queensland
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330321 - 20/07/19 09:22 AM

Great keep us posted on your trials Tinker.

Post Extras: Print Post   Remind Me!   Notify Moderator  
BillG500
.300 member


Reged: 16/10/14
Posts: 129
Loc: Australia
Re: Pitted chambers - a possible solution ? [Re: theprof1]
      #330330 - 20/07/19 12:25 PM

Why at all bother? If it does not affect shooting etc then there really is no need to mess with it. I think there are much better products out there that would work better than dentist goo if you really had to play with it. I'd be buggered if I'd let some hick gunsmith put dentist goo in my double rifle barrels, but you can experiment on yours for sure

Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: BillG500]
      #330332 - 20/07/19 12:51 PM

Quote:

Why at all bother? If it does not affect shooting etc then there really is no need to mess with it. I think there are much better products out there that would work better than dentist goo if you really had to play with it. I'd be buggered if I'd let some hick gunsmith put dentist goo in my double rifle barrels, but you can experiment on yours for sure




Thanks for your consent!

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
BillG500
.300 member


Reged: 16/10/14
Posts: 129
Loc: Australia
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330333 - 20/07/19 02:50 PM

Your welcome Tinker, anytime.

I look forward to the results of your experiments with dentists goo in rifle barrels with great humor


Post Extras: Print Post   Remind Me!   Notify Moderator  
DarylS
.700 member


Reged: 10/08/05
Posts: 27000
Loc: Beautiful British Columbia, Ca...
Re: Pitted chambers - a possible solution ? [Re: BillG500]
      #330335 - 20/07/19 03:07 PM

Quote:

Why at all bother? If it does not affect shooting etc then there really is no need to mess with it. I think there are much better products out there that would work better than dentist goo if you really had to play with it. I'd be buggered if I'd let some hick gunsmith put dentist goo in my double rifle barrels, but you can experiment on yours for sure




I might be wrong.- The Lord knows I've been wrong many times before, but I don't think you've grasped the 'jist' of this fix.
The boys are talking about taking a gun that is virtually unshootable due to chamber pits, and returning it to full function.
As far as I know, aside from re-chambering to a larger, perhaps necked case, this to day has been impossible.

To a functioning rifle, no, but to a gun not shootable due to chamber pits, I'd say, lets experiment.

--------------------
Daryl


"a gun without hammers is like a Spaniel without ears" King George V


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: DarylS]
      #330341 - 20/07/19 03:41 PM

Quote:

...I don't think you've grasped the 'jist' of this fix...




I think you are seeing clearly, Daryl.
There is a great deal of difference between his fantasy goo and metal amalgam.
And that's fine.

And yes Daryl, we are discussing the restoration of function to a gun or rifle (within operating pressure limitations) with metal amalgam.

There are other ways to accomplish this.
Micro-welding is one way to do it. There are actually machines that can get in there and do the work with minimal-to none at all heat affected zone. The process is expensive and not for all applications.
Another way to go is to braze the affected area and re-cut the chamber - this way has greater heat affected zone.
Another way is to sleeve the chambers. This method can work, and some gunbuilders will do it. There have been discussions of catastrophic failures from this method, here (years ago) and on other double rifle sites.
Also there's the re-barreling approach, which is tremendously costly, and with a Damascus gun you can basically forget about finding Damascus replacement tubes.

There's also been the Teague sleeving process which essentially leaves the outer skin if the original tubes intact and full length sleeves are bonded in place.
I haven't heard anything of this process in the last few years. I wonder if the patent process is still available.

Mercury amalgam is basically a metal inlay process.
The resulting inlay is very tough with excellent compressive strength. This process, if it's actually viable (I'm willing to give it a test drive) is a cold process that doesn't require refinish to the barrels and won't affect regulation of a gun or rifle.
I know it's not fantasy goo.
It's ok with me if our friend here wants to maintain his position. More power to him.



Cheers
Tinker

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
Huvius
.416 member


Reged: 04/11/07
Posts: 3556
Loc: Colorado
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330358 - 21/07/19 04:20 AM

When I was a kid, my uncle had a number of old doubles and if they had pits, he would fill them with clear nail polish.
They would hold up for a session or two before dislodging.
Then, clean the chamber with remover and fill them again.
I never watched him do it so I'm not sure if he used a waxed case to smooth the polish or what.

I have wondered if a nickasil plating would work.
Hard as hell and can only be polished with diamond I think.
It's used for replating two stroke cylinders mostly as far as I know.

--------------------
He who lives in the past is doomed to enjoy it.


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: Huvius]
      #330362 - 21/07/19 05:04 AM

Quote:

wondered if a nickasil plating would work.
Hard as hell and can only be polished with diamond I think.
It's used for replating two stroke cylinders mostly as far as I know.




I know that plating has been used to remedy wear at the hook and at the bites. I haven't heard of it being used in chambers, but it's possible. Masking of everything but the pits would allow selective application, as is done at hooks and bites - but it's so much harder than the parent material.


The nail polish remedy is an interesting solution.
Definitely beats re-barreling the gun.

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
BillG500
.300 member


Reged: 16/10/14
Posts: 129
Loc: Australia
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330365 - 21/07/19 07:50 AM

Go for your life guys, I'm not trying to start a shit fight, but just laughing at what you are trying to use. go to any good gunsmith and ask them that you want to use dentist amalgam (goo) or better still ask him to do it for you and see what his reply is. Seriously guy's it's so silly it's laughable. I do get the gist Daryl, if only you read my original reply,

"If it does not affect shooting etc then there really is no need to mess with it"


In the very first line of the this post the original poster said:

"Warning, this is a silly idea of mine so please feel free to call me a dangerous nutter."

Well I'm calling it guys.


Sure there are possibly other ways to do I'm just having a laugh at the original idea. I don't know why you are so defensive. I'm just having a laugh. Take a pill sit back and relax.


Post Extras: Print Post   Remind Me!   Notify Moderator  
93x64mm
.416 member


Reged: 07/12/11
Posts: 4200
Loc: Nth QLD Australia
Re: Pitted chambers - a possible solution ? [Re: BillG500]
      #330366 - 21/07/19 08:37 AM

It regards to joining a double rifle a (High force?) solder is used to perform this task, admittedly this will be difficult to solder inside a barrel; but with an extremely hot piece of iron made to deliver the heat to correct area you should be able to then fill the void (after cleaning & prepping) like the old separate heat sourced soldering irons.
To redo the chamber after a small dab is put on again will be a tense moment, but if set up right & taken very slow with a finishing reamer - I believe doable!
I am no metal smith, so I'm only throwing suggestions out there to far more knowledgeable folks!
To repair an old rifle back to shooting condition certainly is a big ask, but if it was say your great grandfather's & it had history & real semimetal value to you....wouldn't you try to get it going again?


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: 93x64mm]
      #330367 - 21/07/19 09:10 AM

Quote:

It regards to joining a double rifle a (High force?) solder is used to perform this task...





High Force 44 is only good for 38Kpsi.
Also the amalgam is a cold process.
Mercury is some amazing stuff. Science.

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: BillG500]
      #330368 - 21/07/19 09:18 AM

Quote:

amalgam (goo)




The proposal is interesting.
The material is *all metal* and as applied has fantastic compressive strength.

My first impression was something like yours but the proposition has merit.
It's actually worth a try.

This discussion isn't about "something someone is trying to do" rather it's a discussion of "something that could actually be a good solution"

But goo.
Really, my guy.
Goo.
55Kpsi metal goo...
Your reaction is pretty entertaining.

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
Postman
.375 member


Reged: 25/09/13
Posts: 846
Loc: Canada
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330369 - 21/07/19 11:20 AM

Before filling with amalgam, would you first perform a root canal procedure? MUST remove the rot before attempting to fill. Not certain amalgam will stick properly. If it does, well why the hell not??? Maybe the black light epoxy would be more effective? If you can’t recut the chamber to a larger cased round of same caliber as would be one of the traditional and sometimes viable fixes and the rifle is otherwise effectively useless in it’s present form, well just maybe the concept has merit.

Remember, many wonderful ideas in this world started with an idea most thought was lunacy..... Hell, many thought the moon was made of cheese before we landed people up there!!!!!!!!!


Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: Postman]
      #330370 - 21/07/19 11:31 AM

Quote:

Before filling with amalgam, would you first perform a root canal procedure? ... Hell, many thought the moon was made of cheese before we landed people up there!!!!!!!!!




I'm sure it needs to be free of rust and debris, likely needs a bit of undercut too.

On that cheese VS rock business, there are plenty of fellows who don't believe that we ever got there, and many who don't believe our planet is shaped like a sphere.
We might have some of the flat-planet wizards among us here on the site!

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
eagle27
.400 member


Reged: 24/01/09
Posts: 1165
Loc: Rolleston, Christchurch, New Z...
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330371 - 21/07/19 12:39 PM

Amalgam, solder!!!!! there's newer better products that will do the job. I've used Loctite liquid metal in various applications in conjunction with Loctite cleaner and prep. There's a couple of different liquid metal products, the two tube epoxy liquid metal the one I have used. The colour is grey so will more or less match the chamber colour.

Once the pit is filled and hardened, a piece of dowel with a wrap of fine wet and dry paper will smooth out the filled pit.


Post Extras: Print Post   Remind Me!   Notify Moderator  
theprof1
.224 member


Reged: 01/02/19
Posts: 33
Loc: Queensland
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330372 - 21/07/19 12:44 PM

I was hoping the rust would be removed with the hydrochloric acid leaving a fairly sharp surface profile for the amalgam to get a grip on. there may be better more efficient chemicals than HCL though, I would avoid those converters that leave a smooth shiny deposit behind..

Post Extras: Print Post   Remind Me!   Notify Moderator  
tinker
.416 member


Reged: 12/03/05
Posts: 4835
Loc: Nevada
Re: Pitted chambers - a possible solution ? [Re: theprof1]
      #330374 - 21/07/19 01:36 PM

I'm sure it depends on the pitting.
I might just cut a somewhat dovetailed channel and do some inlay. Have a look, so to speak.

--------------------
--Self-Appointed Colonel, DRSS--



"It IS a dangerous game, and so named for a reason, and you can't play from the keyboard. " --Some Old Texan...


Post Extras: Print Post   Remind Me!   Notify Moderator  
DarylS
.700 member


Reged: 10/08/05
Posts: 27000
Loc: Beautiful British Columbia, Ca...
Re: Pitted chambers - a possible solution ? [Re: tinker]
      #330375 - 21/07/19 03:48 PM

I was also thinking of an undercut to hold it in place.
The pits might be pits as caused by a corrosive, as in primer or in the powder itself.
If so, the pits might just be undercut already, like chlorate and perclorate fouling does to some steels, rather than simple dished-shaped pits caused by normal rust/oxidation.
Either way, they must be thoroughly cleaned. In the chlorate damage, there might already be the fill-holding undercut.
Getting a good look with a Hawkeye bore scope should show the nature of the pits.

--------------------
Daryl


"a gun without hammers is like a Spaniel without ears" King George V


Post Extras: Print Post   Remind Me!   Notify Moderator  
Pages: 1 | 2 | >> (show all)



Extra information
0 registered and 66 anonymous users are browsing this forum.

Moderator:  CptCurl 

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 8994

Rate this topic

Jump to

Contact Us NitroExpress.com

Powered by UBB.threads™ 6.5.5


Home | Ezine | Forums | Links | Contact


Copyright 2003 to 2011 - all rights reserved