Rule303
.450 member
Reged: 05/07/09
Posts: 5095
Loc: Woodford Qld
|
|
Nice. Might only be a 2 shot group but the followup shot is going to be close to the first and both straight down the middle. Good shooting Neale with a very nice rifle and calibre.
Cheers
Greg
|
FATBOY404
.400 member
Reged: 14/11/09
Posts: 1730
Loc: QLD
|
|
Thanks Greg.
The reason there is two shots is I fired one and then my mate asked if he could fire one. Not bad as I am left handed and he right handed.
-------------------- "WHATEVER BLOWS YOUR HAIR BACK"
Edited by FATBOY404 (23/08/11 06:34 AM)
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27171
Loc: Beautiful British Columbia, Ca...
|
|
Amazing shot placement for 2 different guys. I have the same situation with one of my friend. We could sight each other's rifles - that doesn't happen as often as one might think.
My brother and I are close to 3" apart at 100 meters - with a scoped rifle yet.
20" at 400 shows excellent range for that bullet - how high at 100?
-------------------- Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
FATBOY404
.400 member
Reged: 14/11/09
Posts: 1730
Loc: QLD
|
|
About 2.5 inches high at 100 yards Daryl.
I find I can shoot most right handers rifles and true up some of their rifles for them as they dont get a lot of time.
-------------------- "WHATEVER BLOWS YOUR HAIR BACK"
|
buckbrush
.300 member
Reged: 23/08/07
Posts: 120
Loc: Alberta
|
|
that behind the grip stock feature was called a "chin strap" by some American custom stock maker, I can not recall who at the moment.
|
xausa
.400 member
Reged: 07/03/07
Posts: 2037
Loc: Tennessee, USA
|
|
Quote:
that behind the grip stock feature was called a "chin strap" by some American custom stock maker, I can not recall who at the moment.
Tom Shelhamer
|
FATBOY404
.400 member
Reged: 14/11/09
Posts: 1730
Loc: QLD
|
|
Quote:
that behind the grip stock feature was called a "chin strap" by some American custom stock maker, I can not recall who at the moment.
It has been done before hey ?.
We thought it was a first. "nothing new under the sun" .
-------------------- "WHATEVER BLOWS YOUR HAIR BACK"
|
DarylS
.700 member
Reged: 10/08/05
Posts: 27171
Loc: Beautiful British Columbia, Ca...
|
|
Very litte new at any rate - some muzzleloaders have had them - pistol gripped rifles, of course. That limits countries of origin and period, of course.
I'm sure I saw an English Sporting rifle of the 1850-60 period with that 'chin strap'- raised panel around the crip cap. Too, they were common on some plains rifles around the bottom of the cheek piece and behind the tangs.
Quite normal on Sharps as well, forward from the bottom of the action - that would put them 1874 through 1885 anyway.
This in no way, detracts from their form and good looks.
-------------------- Daryl
"a gun without hammers is like a Spaniel without ears" King George V
|
m4220
.300 member
Reged: 04/02/07
Posts: 234
Loc: wa
|
|
Shelhamer chin strap, signature treatment 1940 & on, named after Tom Shelhamer who did stock work for A.O. Niedner's shop in Dowagiac, Michigan. Have seen this same chin strap treatment on a Franz Sodia 98 Mauser from Ferlach that I have as well. I think it originated in Germany/Austria but was a signature detail used by Shelhamer after 1940 and became known as the Shelhamer chinstrap. It is a nice feature that make a custom stock stand out. I have been building up a 8x68S and should be shooting soon, Can't wait!
m4220
Edited by m4220 (24/10/13 01:49 PM)
|
gwh
.333 member
Reged: 28/01/08
Posts: 277
Loc: Cairns Australia
|
|
Very nice
-------------------- Hunt hard, shoot straight
"I speak of Africa and golden joys; the joy of wandering through lonely lands; the joy of hunting the mighty and terrible lords of the wilderness, the cunning, the wary and the grim"
Theodore Roosevelt, Khartoum, 1910
|
Rhodes
.275 member
Reged: 20/09/11
Posts: 94
Loc: NQ, Australia
|
|
Quote:
Well I have got my 8x68s finnished. It is built on a zkk 600 action opended up by a couple of mm's. I am loading 200 grain Woodleigh PP and Speers with 72 grains of 2209 with a c.o.l of 90mm for 3000 fps.
The barrel is a 26" #722 Lothar Walter supplied by Axel(HuntingSchneider)on NE.
All bits and pieces came from Greame Sraggon (0427319589)grip cap and sling swivels.
Daryl Stevens (0419772048) suppiled the timber and did all the stock work.
Hi Fatboy404
sorry for dragging up an old thread but maybe you could help.
You mentioned that you used a Lothar Walther #722 barrel for this build. I see on the Lothar Walther website they have pre-chambered / pre-fit #722 profile, 26" barrels threaded to suit M98 actions available. Is this the barrel used for this build or is the BRNO ZKK specific thread different to a M98?
I ask because I intend to re-barrel a ZKK 600 and am looking at grabbing on of these barrels in 9.3.
|
Viking338
.333 member
Reged: 11/08/11
Posts: 480
Loc: Queensland Australia
|
|
Hi Rhodes, I know the tread cut is definitely different. Also I know this rifle well and have shot it at Neale’s place. He did order the barrel as chambered but un-threaded for this reason. I know it is dearer to order one un-cut as they normally just thread them all for Mauser’s and it is considered a special order to get one chambered but not threaded.
Hope this helps
Steve
|
Rhodes
.275 member
Reged: 20/09/11
Posts: 94
Loc: NQ, Australia
|
|
Thanks Steve,
that's a big help. Thanks for clearing that up for me. I read Frank DeHaas' book and he suggests the BRNO action is based on the M98 but doesn't mention any thread difference. He also doesn't show a separate barrel stub drawing for the BRNO like he does for the other M98 derivatives so I wasn't sure.
I'm making inquiries with a barrel distributor at the moment and yes, he did mention the extra cost for a non shelf item (M98 thread) barrel. I'm just trying to find a profile now that will match the factory ZKK 600 barrel close enough to use the factory stock.
If Lothar Walther don't cut the ZKK thread I'll have a chat to the gunsmith when he gets back from holidays about cutting the threads to suit if I order an un-threaded barrel stub as you suggest.
Apologies again for the off topic thread dig everyone. Hopefully it will help someone taking on a similar project.
Cheers Darren
|
Viking338
.333 member
Reged: 11/08/11
Posts: 480
Loc: Queensland Australia
|
|
No worries Darren, glad to help. I think the #722 profile Neale ordered is very sexy on his rifle. I doubt you would go wrong with that profile.
Cheers
Steve
|
Homer
.416 member
Reged: 07/04/09
Posts: 3081
Loc: Canberra, Australia
|
|
Mmmmmmmmmmmmmmmmmmmmmmmmmmmm Donuts!
Avagreatweekendeh! Homer
-------------------- "Beware the Lolly Pop of Mediocrity,
Lick it Once and You Will Suck Forever"
|
NitroX
.700 member
Reged: 25/12/02
Posts: 40056
Loc: Barossa Valley, South Australi...
|
|
Quote:
Hi Rhodes, I know the tread cut is definitely different. Also I know this rifle well and have shot it at Neale’s place. He did order the barrel as chambered but un-threaded for this reason. I know it is dearer to order one un-cut as they normally just thread them all for Mauser’s and it is considered a special order to get one chambered but not threaded.
Hope this helps
Steve
Hi Viking338, how is Neale going? Still in touch with him?
-------------------- John aka NitroX
...
Govt get out of our lives NOW!
"I love the smell of cordite in the morning."
"A Sharp spear needs no polish"
|
Viking338
.333 member
Reged: 11/08/11
Posts: 480
Loc: Queensland Australia
|
|
Hi John, yes we talk every week and I go and stay with him several times a year (he lives seven hours from me). He works very hard at his new place of employment. He has gotten into hunting with a bow lately (as have I) to expand his hunting options and skills.
Kind regards Steve
|