VonGruff
.400 member
Reged: 08/02/09
Posts: 1119
Loc: South Otago, New Zealand.
|
|
What would you all think of as the best barrel profile for a 318 WR. The barrel is going to be a one off so wont have to stick with factory profiles. I will be stocking the rifle as iron sights only so I have taken that into account when putting together a proposed profile Starting with the Kreiger page and the #3 medium sporter with these changes Finished at 25 inches .570 at the muzzle ie .120 either side over groove dia this will keep it from being muzzle heavy but have enough to hang nicely in hand I would reduce the neck dia (G) to .815 and all up this should keep the finished weight just under the 3 lb mark to keep the rifle nice and portable but still have the weight where it will enhance the handling.
-------------------- Von Gruff.
Exodus 20:1-17
Acts 4:10-12
|
BillG500
.300 member
Reged: 16/10/14
Posts: 129
Loc: Australia
|
|
My opinion for what it's worth after carrying rifles for hours that are just that little bit too heavy, is go light. I built myself a lovely .404 on a Brno 602 single bridge action, unfortunately I made it too heavy and it is a pig to carry on extended hunts. I just used a standard sporter barrel, as I thought it would be the better option. Since building the .404 I have handled a couple of Mauser's an 8mm, 9.3x62 & another .404, all these rifles were very light compared to my .404 and it was a delight to hold them and I know to carry and hunt with these would be a dream compared to what I own. My .338 WM that I use and love could also be that 1/2 lb lighter as it weighs 9.2lb scoped. I also own a .500 NE and it weighs up into the 11lb range and is also a bit heavy after a days hunting, but I'll put up with this one  I intend to, after I finish my enfield sporter in .303/25 to build another .404 on a standard length 98 and either a .318 WR or .338WM again on a 98. Both of these will be light, not featherweight but pretty light all the same so I can carry it with ease. I'm not at all concerned about any added recoil, when your hunting you only take a couple of shots and I don't really feel the recoil hunting, just like almost everyone. So personally I'd go the light sporter for the reasons above, and 8.5lb all up weight to be about optimum for a rifle that will get carried a fair bit. What action do you plan to use? Anyway good luck with the build.
|
VonGruff
.400 member
Reged: 08/02/09
Posts: 1119
Loc: South Otago, New Zealand.
|
|
The guy it is being built for has shown a preference for a slightly heavier barrel than I sugested but it is his rifle so that is what it will get. Going to follow this style
 With these dimensions

Will be building it on an FN action
-------------------- Von Gruff.
Exodus 20:1-17
Acts 4:10-12
|
BillG500
.300 member
Reged: 16/10/14
Posts: 129
Loc: Australia
|
|
Looking forward to your progress.
Enjoy
|
ducmarc
.400 member
Reged: 14/07/14
Posts: 1207
Loc: fla
|
|
Is 25" the optional length? And what sights are u going to use?
-------------------- 'killed by death' Lemmy.. ' boil the dog ' Elvis Manywounds "my best friend is my magnum forty four" hank willams the third.
|
Homer
.416 member
Reged: 07/04/09
Posts: 3081
Loc: Canberra, Australia
|
|
G'Day Fella's,
Von Gruff, Mmmmmmmmmmmmmmmmmmmmmmmmmmm Donuts!
last week, I sent some images to Ripp, of a restored original WR repeating rifle, in .318 WR Accelerated Express. Unfortunately this rifle is no longer in my safe, so I can't go measure it up! Bugger! Von Gruff, how about I email you the same details?
Regards Homer
-------------------- "Beware the Lolly Pop of Mediocrity,
Lick it Once and You Will Suck Forever"
|
RugerBoy
.224 member
Reged: 18/08/12
Posts: 8
Loc: South Africa
|
|
Looking forward to see the progress, will start a similar project in a couple of months. I'm also planing on using a FN action, a Walther barrel and a beautiful piece of exhibition grade Turkish walnut.
Planing to follow the lines of a original WR building a light weight rifle.
Any more info would be appreciated.
Regards,
|
93x64mm
.416 member
Reged: 07/12/11
Posts: 4412
Loc: Nth QLD Australia
|
|
Quote:
G'Day Fella's,
Von Gruff, Mmmmmmmmmmmmmmmmmmmmmmmmmmm Donuts!
last week, I sent some images to Ripp, of a restored original WR repeating rifle, in .318 WR Accelerated Express. Unfortunately this rifle is no longer in my safe, so I can't go measure it up! Bugger! Von Gruff, how about I email you the same details?
Regards Homer
I think we'd all like to see those mate!!!!
|
justcurious
.333 member
Reged: 17/03/10
Posts: 285
Loc: Germany
|
|
My aproach is different. Here the Oberndorf action for ,318 . Small radius cut in the front ring. Magazine box 88 mm long (Standard is 84 mm). Made 1924 Large ring but small threaded. All the furniture Type A. The same action used for 30-06. Will it be a .318 again. No will become 30-06. The same old history but a better future. http://up.picr.de/27497359wr.jpg

Edited by justcurious (21/11/16 11:35 PM)
|