Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: making 6,5x53R brass

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Shooting & Reloading - Mausers, Big Bores and others >> Mannlicher Discussion forum & Archive

Pages: 1

lancaster
.470 member

Reged: 06/05/08
Posts: 8731
Loc: There's a lighthouse in the mi...

making 6,5x53R brass
#264282 - 27/04/15 10:28 PM

my 6,5x54MS die set( a 6,5x53R rimless) came today and so I start making 6,5x53R out of 303 Brit military brass. I was feeling - after years of reloading you have it in the finger tips - and seeing the shoulder of the 303 brass was a little bit brittle so first step was full length with a 308 Winchester die. this sets the shoulder back and was than followed by a 6,5x57 full length die for giving the neck a good start.

from left to right
303
303 shoulder collapsed
fl resized in 308 Win.
fl resized in 6,5x57
fl resized in 6,5x54MS
cut to 53,5mm
original 6,5x53R

this way I lost only one other case from 150 when the neck was sticking in the die

hope this could help, you can take a 6,5x55 FL die also

--------------------
Norwegian hunter misses moose, shoots man on toilet
.
bringing civilisation to the barbarians

Edited by lancaster (27/04/15 10:29 PM)

Post Extras:

DarylS
.700 member

Reged: 10/08/05
Posts: 26514
Loc: Beautiful British Columbia, Ca...

Re: making 6,5x53R brass [Re: lancaster]
#264291 - 28/04/15 12:58 AM

Well done. The 20 degree shoulder of the .308 prevented the crushing of the .303's sharp shoulder. This was a very important step.

In the same line of thinking, I now use a shortened .17Rem die for initial necking of .22 Hornet's to .17Cal. for my .17AH's.

--------------------
Daryl

"a gun without hammers is like a Spaniel without ears" King George V

Post Extras:

Huvius
.416 member

Reged: 04/11/07
Posts: 3525
Loc: Colorado

Re: making 6,5x53R brass [Re: DarylS]
#264296 - 28/04/15 04:22 AM

Very nice.
I have correct brass for my 6.5s but one guy I know prefers to use resized 303 brass.
Maybe just based on cost and availability and done as you have, is a very good option.

--------------------
He who lives in the past is doomed to enjoy it.

Post Extras:

lancaster
.470 member

Reged: 06/05/08
Posts: 8731
Loc: There's a lighthouse in the mi...

Re: making 6,5x53R brass [Re: Huvius]
#264300 - 28/04/15 05:25 AM

actually this startet with 1600 RWS 6,34mm Berdan primer I had no other use than looking for 303 military brass because this is the only brass for this primer size. Sarg send me the cases from new zealand around the world just to play dandy here

http://forums.nitroexpress.com/showflat.php?Cat=0&Number=237915&an=0&page=3#Post237915

--------------------
Norwegian hunter misses moose, shoots man on toilet
.
bringing civilisation to the barbarians

Edited by lancaster (28/04/15 05:32 AM)

Post Extras:

93x64mm
.416 member

Reged: 07/12/11
Posts: 3987
Loc: Nth QLD Australia

Re: making 6,5x53R brass [Re: lancaster]
#264302 - 28/04/15 06:04 AM

Don't forget to anneal the neck & shoulder areas, otherwise all that good work may go out the window on first firing!
93x64mm

Post Extras:

Waidmannsheil
.400 member

Reged: 19/04/13
Posts: 2387
Loc: Melbourne Australia

Re: making 6,5x53R brass [Re: 93x64mm]
#264303 - 28/04/15 06:11 AM

By the way, Bertram Brass does make the 6.5x53R with the correct head stamp. However well done Lancaster, your cases seem to have come out very well.

Waidmannsheil.

--------------------
There is nothing wrong with vegetarian food, so long as there is meat with it.

Post Extras:

Ash
.400 member

Reged: 10/05/11
Posts: 1653
Loc: Australia

Re: making 6,5x53R brass [Re: Waidmannsheil]
#264304 - 28/04/15 06:50 AM

He used military 303 as a way to use his primer cache. Ha! Makes sense!
Turned out good, Lancaster. Ive heard Winchester brass can be run straight into the 6.5x54 die?

Anyone try that?

--------------------
.

Post Extras:

lancaster
.470 member

Reged: 06/05/08
Posts: 8731
Loc: There's a lighthouse in the mi...

Re: making 6,5x53R brass [Re: Ash]
#264337 - 29/04/15 12:46 AM

maybe seems strange but my berdan cases are worth more than boxer cases. its the only way to use the berdan primer I have and berdan primed brass became more and more rare.
I bought 100 once fired 8x57IS military cases just to use my 5,5mm berdan primer.
resizing the 303 brass without anealing will be a hopeless game not to mention the fact this brass had a 1957 headstamp and was brittle only by the years it have seen.
think Winchester 303 is made by Sellier&Bellot, I have some of this cases and you can form 6,5x53R without problems. my 303 military brass have a very thick base, maybe 11,56mm so I turn it down to 11,43mm on the lathe. this is the base diameter of the 6,5x54MS die.

--------------------
Norwegian hunter misses moose, shoots man on toilet
.
bringing civilisation to the barbarians

Post Extras:

Sarg
.400 member

Reged: 20/01/07
Posts: 1365
Loc: Nil

Re: making 6,5x53R brass [Re: lancaster]
#264349 - 29/04/15 06:24 AM

Thank you for the Thank you Lancaster, I had no idea you were going to make 6.5X53R out of them, a LOT of work has gone into those case's

Yes I found the head a bit large on Exmil case's, new unfired Rem or Win is much easier I think, more so if trying to load in a sporter that may have a tighter chamber !

I don't lose any if I sneak into my mates reloading shop & use all his dies from 308Win, 7mm/08, 260 then into 6.5X54 dies, boy do they shoot great in my Gibbs, the barrel is like brand new as I don't think it has been shot much if at all, unfortunately it has no bolt & I use the one from my Exmil Steyr !

Always great to read your posts, thanks again !

Post Extras:

Marrakai
.416 member

Reged: 09/01/03
Posts: 3482
Loc: Darwin, Top End of Australia

Re: making 6,5x53R brass [Re: Sarg]
#264369 - 29/04/15 11:45 PM

Cases made from .303 will be just a few thou wider across the rim, which doesn't matter a hoot in the rifle action or chamber, but in my experience will eventually slacken the charger clips to the point where they require constant bending and never seem to be quite right thereafter.

Having said that, its what I use in mine, with perseverance, and a little cussing occasionally...

Just doesn't seem worth it to turn a couple of thou off each rim.

--------------------
Marrakai
When the bull drops, the bullshit stops!
--------------------------------
www.marrakai-adventure.com.au

Post Extras:

Carpetsahib
.333 member

Reged: 29/04/07
Posts: 435
Loc: Western NC

Re: making 6,5x53R brass [Re: lancaster]
#264373 - 30/04/15 04:24 AM

This is an interesting post. Something that makes a radical re-sizing operation more successful is to utilize the seating dies as forming dies. Simply remove the seating stem and use the die as a sizer. Doing this, I was able to transform .444 Marlin brass into 7x57R brass with little difficulty.

Post Extras:

Ireload2
.224 member

Reged: 11/08/13
Posts: 41
Loc: USA

Re: making 6,5x53R brass [Re: Carpetsahib]
#264436 - 01/05/15 03:53 PM

I make 6.5X53R Dutch using 3 dies.

I push the shoulder back with a 7.35 Carcano FL die made by RCBS. The base is larger than some other brands so it does not squash the heads undersize.

Then I form the neck down to .299 using a Pacific 6.5 Carcano trim die.

Make sure you leave the shoulder about .005 to .010 long with the Carcano dies.

Then I form in a 6.5X53R trim die and cut off the case with a trimmer or in a lathe.
I fit the head to shoulder length exactly to my rifle's chamber so it effectively headspaces on the shoulder.

From here I can neck size with a 6.5X55 FL die.

For normal reloading I use RCBS 6.5X53R dies. My dies are about .452 to .453 at the head which is a good close fit to my chamber.

6.5X54 MS dies are closer to .448 at the base and do not work for me in spite of what others say.

Post Extras:

lancaster
.470 member

Reged: 06/05/08
Posts: 8731
Loc: There's a lighthouse in the mi...

Re: making 6,5x53R brass [Re: Ireload2]
#264479 - 02/05/15 09:28 PM

so its done
brass trimmed, base lathe turned, neck and shoulder again anealed

see the brass became very hard again after I swage it down so anealing it again was necessary. little bit fireforming will be anyway because the 303 should is smaller than the .256 Mannlicher.

use my old 12 ga RCBS die set for primming, is just a toolbox for doing anything you can not do with the common stuff. to bad they dont make this dies anymore.

working with LR primer is boring

--------------------
Norwegian hunter misses moose, shoots man on toilet
.
bringing civilisation to the barbarians

Edited by lancaster (03/05/15 12:43 AM)

Post Extras:

Sarg
.400 member

Reged: 20/01/07
Posts: 1365
Loc: Nil

Re: making 6,5x53R brass [Re: lancaster]
#264496 - 03/05/15 07:47 AM

Looking good Lancaster, as I said before a lot of work done on those cases, seems strange to see CAC (Colonial, Ammunition, Co) head stamp in far off Germany, 100yrs-75yrs ago I would be shot for suppling ordnance

The US will not even send me a 5 shot magazine for a 80yr .22 Winchester bolt action, yet they (with Australian help ?) sent Small Arms & ammunition (including Rocket launchers) to Syrian Rebels, which have now turned into ISIS, so supplied Terrorists !

Ok to send Military Weapons to nice safe peaceful Middle Eastern Terroists, but not send a mag for a Bunny Gun down to War Mongering Crazy Kiwis !

Post Extras:

lancaster
.470 member

Reged: 06/05/08
Posts: 8731
Loc: There's a lighthouse in the mi...

Re: making 6,5x53R brass [Re: Sarg]
#264506 - 03/05/15 12:58 PM

being a white male hetero with legal owned sporting guns who pay taxes and work for his living you are the public enemy number one in the western society's today so it make sense.

--------------------
Norwegian hunter misses moose, shoots man on toilet
.
bringing civilisation to the barbarians

Edited by lancaster (03/05/15 01:01 PM)

Post Extras:

Pages: 1

Extra information

1 registered and 74 anonymous users are browsing this forum.

Moderator: CptCurl

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 12351

Jump to

NitroExpress.com

Home | Ezine | Forums | Links | Contact