Home | Ezine | Forums | Links | Contact
NitroExpress.com: anyone have blueprints?

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies


*** Enjoy NitroExpress.com? Participate and join in. ***

Double Rifles, Single Shots & Combinations >> Building Double Rifles & Gunsmithing

Pages: 1
castlead
.224 member


Reged: 06/08/10
Posts: 6
Loc: washington
anyone have blueprints?
      #170513 - 29/10/10 06:55 AM

Hello to all, I am new to this whole forum thing, and this is my 3rd post ever, (Posted two in the humor section as a test)

I have fallen in lust with double rifles, but being a little short on funds, am unable to afford one at the present time. However I am a very talented machinist, and decided that I will build my own. I just need plans for an action. I figure this will be both an education and a fun journey full of cuss words and bloody fingers, and will probably cost more than just buying one, so I figured it would be perfect for me!

Here is what I want to build; a double hammer gun, with a Jones under lever, and double triggers. I want it to be chambered in something that I am going to use, and not expensive to shoot, but having a little history to it as well. The venerable 30-30 Winchester fit’s the bill to a “T”. Good on dangerous deer to 150 yards, and will stop a charging raccoon at 5 paces with a well placed brain shot.

So… does anyone have blue prints (machinist drawings) for an action like this? Any info on heat treating and type of steels to use would be helpful as well.


Post Extras: Print Post   Remind Me!   Notify Moderator  
CptCurlAdministrator
.450 member


Reged: 01/05/04
Posts: 5284
Loc: Fincastle, Botetourt County, V...
Re: anyone have blueprints? [Re: castlead]
      #170523 - 29/10/10 09:16 AM

Welcome aboard, castlead.

You are infected with a serious disease - double rifles!

There is no cure. God help you.

Curl

--------------------
RoscoeStephenson.com

YOUR DOUBLE RIFLE IS YOUR BEST FRIEND.



Post Extras: Print Post   Remind Me!   Notify Moderator  
4seventy
Sponsor


Reged: 07/05/03
Posts: 2210
Loc: Queensland Australia
Re: anyone have blueprints? [Re: castlead]
      #170524 - 29/10/10 09:26 AM

Welcome castlead!
A couple of members here have built hammerless actions from scratch, not sure if anyone has done a hammered action though.
There is plenty of knowledge and expertise regarding building doubles on this forum, so you have come to the right place.
Looking forward to hearing all about your project as it comes together, so please keep us informed.


Post Extras: Print Post   Remind Me!   Notify Moderator  
oupa
.300 member


Reged: 01/03/06
Posts: 127
Loc: Maryland,USA
Re: anyone have blueprints? [Re: castlead]
      #170530 - 29/10/10 10:31 AM

Welcome. You have stumbled upon in my opion the most experienced group in cyberspace regarding this passion. My own present project is a sidelock hammer gun converted to .30-30Win.! Not as talented or ambitious though I started with an existing shotgun action... well, most of one anyway. Maybe someone can provide the drawings you seek but if not reverse engineering is pretty straight forward if you can get your hands on even an ancient shotgun of the type desired. Even lacking that the mechanics of a double gun are not all that complicated... until you try putting it together at least, and a rudimentary understanding of what's needed can be arrived at from even crude sketches and very different action styles. Unless you are a purist who seeks to exactly replicate a specific firearm I think you'll be able to work it out. Good luck and please keep us posted on your progress!

Post Extras: Print Post   Remind Me!   Notify Moderator  
baileybradshaw
.333 member


Reged: 21/06/08
Posts: 305
Loc: Diana, TX
Re: anyone have blueprints? [Re: oupa]
      #170667 - 31/10/10 02:20 PM

Castlead,

Your best bet will be to buy an old action and reverse engeneer it. The Jones underlever is pretty simple once you see it in detail, and if you don't make it with self cocking locks, you have a very simple action.

Steel of choice would be 8620. Plan on case hardening it after engraving. There are several shops that you can send it to for color case hardening, Doug Turnbull being at the head of the pack.

Lock parts such as springs, sears, firing pins and some screws I make from 1084 steel.

You can build a 30-30 on a nice petite action that will feel alive.

I wish I knew of a source for machinist drawings. Would have saved me hundereds of hours. Lots if inexpensive shotguns here to use as a pattern though.

http://www.simpsonltd.com/index.php?cPath=350_354&osCsid=9d80919c17709696f93daf6062ae559c

Best of luck!!

--------------------
www.bradshawgunandrifle.com


Post Extras: Print Post   Remind Me!   Notify Moderator  
whitey
.275 member


Reged: 20/01/10
Posts: 83
Loc: Colorado, USA
Re: anyone have blueprints? [Re: baileybradshaw]
      #170718 - 01/11/10 02:54 AM

And they are very good to work with you. Whitey

Post Extras: Print Post   Remind Me!   Notify Moderator  
castlead
.224 member


Reged: 06/08/10
Posts: 6
Loc: washington
Re: anyone have blueprints? [Re: castlead]
      #170819 - 02/11/10 11:28 AM

Thanks for the info guys, I shall track down an old shotgun action and reverse engineer. I will keep you posted on my progress as it happens. But right now I am going to be out of action for a couple of months, as I am in the middle of moving to the other side of the country. It is amazing how much crap one accumulates when you settle down for a few years! Castlead out!

Post Extras: Print Post   Remind Me!   Notify Moderator  
Carpetsahib
.333 member


Reged: 29/04/07
Posts: 435
Loc: Western NC
Re: anyone have blueprints? [Re: baileybradshaw]
      #170918 - 05/11/10 10:01 AM

Quote:

Steel of choice would be 8620. Plan on case hardening it after engraving. There are several shops that you can send it to for color case hardening, Doug Turnbull being at the head of the pack.


SAE 8620 is a great choice. It happens to be the steel that is used for Constant Velocity Joints (Outer Races, Inner Races and Cages). After case hardening to a depth of .008 to .010 in., the parts become extremely wear resistant and tough.

Post Extras: Print Post   Remind Me!   Notify Moderator  
AkMike
.416 member


Reged: 19/11/05
Posts: 2576
Loc: Anchorage, Alaska
Re: anyone have blueprints? [Re: castlead]
      #170947 - 05/11/10 02:25 PM

Quote:

I shall track down an old shotgun action and reverse engineer.




Just remember that all shotgun actions are not created equal.

--------------------
"When you see that in order to produce, you need to obtain permission from men who produce nothing; when you see that money is flowing to those who deal not in goods, but in favors; you may know that your society is doomed." Ayn Rand


Post Extras: Print Post   Remind Me!   Notify Moderator  
baileybradshaw
.333 member


Reged: 21/06/08
Posts: 305
Loc: Diana, TX
Re: anyone have blueprints? [Re: AkMike]
      #170954 - 05/11/10 03:13 PM

There is a good article in Shooting Sportsman ( Sept or Oct issue) by Vic Venters on smoking in barrels "on the circle". It illustrates the major points to consider in fitting barrels to the action. While it is certainly true that not all guns are created equal, the article shows where a little more material can be added to increase strength of the action and make it suitable for a rifle.

The same issue has an article by Steven Huges illustrating a box lock action. Another good reference for technical information is "Shotgun technicana" by McIntosh.

A 30-30 won't stress many actions, but the better it is built, the more generations get to enjoy it.

--------------------
www.bradshawgunandrifle.com

Edited by baileybradshaw (05/11/10 03:17 PM)


Post Extras: Print Post   Remind Me!   Notify Moderator  
tarawa
.333 member


Reged: 21/10/07
Posts: 420
Loc: South Florida
Re: anyone have blueprints? [Re: baileybradshaw]
      #171108 - 08/11/10 06:32 AM

Castlead,
Check the black powder section for a maker that uses the handle "cowboycs" (I think). I believe that he made a Jones under lever gun. either a single or a double. Not sure but he should be able to answer your questions.

--------------------
Life is for Service

Edited by tarawa (08/11/10 06:46 AM)


Post Extras: Print Post   Remind Me!   Notify Moderator  
Pages: 1



Extra information
0 registered and 31 anonymous users are browsing this forum.

Moderator:  CptCurl 

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 1863

Rate this topic

Jump to

Contact Us NitroExpress.com

Powered by UBB.threads™ 6.5.5


Home | Ezine | Forums | Links | Contact


Copyright 2003 to 2011 - all rights reserved