Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: Photos of claw mounts for MS rifles.

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Shooting & Reloading - Mausers, Big Bores and others >> Mannlicher Discussion forum & Archive

Pages: 1

GG375
.333 member

Reged: 27/02/04
Posts: 347
Loc: Brisbane

Photos of claw mounts for MS rifles.
#129372 - 12/03/09 06:56 PM

Guys

Have just received another set of EAW claw mounts for my next MS project and thought you might like to have a look.

These are for a modern Khales 2x - 7x scope. I don't have a rifle to put them on yet but I'm working on that. I will sell my 1903 takedown and hope to find a 1950 model 6.5. I'll restock and have these mounts and the scope fitted - and have a little brother for my 9.3

Cheers.

GG

Edited by CptCurl (15/03/10 10:09 PM)

Post Extras:

ozhunter
.400 member

Reged: 18/08/04
Posts: 1692
Loc: Sydney, Australia

Re: Photos of claw mounts for MS rifles. [Re: GG375]
#129737 - 16/03/09 08:52 PM

Nice pieces there mate.
My gun smith uses Recknagel swing mounts which aren't bad ether.

Post Extras:

hoser
.275 member

Reged: 06/01/10
Posts: 86
Loc: California, USA

Re: Photos of claw mounts for MS rifles. [Re: ozhunter]
#150398 - 12/01/10 06:04 PM

Anyone else have additional pix of claw mounts?

Post Extras:

JabaliHunter
.400 member

Reged: 16/05/07
Posts: 1958
Loc: England

Re: Photos of claw mounts for MS rifles. [Re: hoser]
#150423 - 12/01/10 11:58 PM

Just a tip with EAW/Apel rings - because you have to stretch them over the scope tube, put some plastic tape over the tube first. Then when the ring is on the tube, move it out of the way and remove the tape before lining up the scope and clamping the rings. You'll avoid any marks on the scope tube that way. My 30mm rings were very tight to get onto the scope tube...

Post Extras:

KurtC
.224 member

Reged: 28/08/07
Posts: 17
Loc: NJ, USA

Re: Photos of claw mounts for MS rifles. [Re: hoser]
#155744 - 08/03/10 06:49 AM

Quote:

Anyone else have additional pix of claw mounts?

These are on a 1950 half stock 9.3x62 proofed in 1954. The front uses a saddle base on the receiver ring. The rear ring appeared to be a replacement, as the styling is more squared.

Edited by CptCurl (15/03/10 10:10 PM)

Post Extras:

Kiwi_bloke
.333 member

Reged: 03/09/09
Posts: 256
Loc: New Zealand

Re: Photos of claw mounts for MS rifles. [Re: KurtC]
#158169 - 03/04/10 09:26 PM

I watched a set of Rechnagel mounts fitted, not Mannlicher ones, (though they do make them), but the top rings were more than a half circle. To spring them, the installer placed an allen key in each of the 2 grub screws on both sides and simply tensioned them backwards to open the ring up. No scratches that way. A trick worth knowing.

Some of the oldest factory-made rings, such as the Akah rings I had on a 1935 Mauser 9x57, can't be separated in the usual way and the Landlicht scope needed to be dismantled to slide them onto the centre tube. They had enough adjustment then to be nipped up to tighten.

Post Extras:

André
.333 member

Reged: 28/06/04
Posts: 254
Loc: Brussels (Belgium)

Re: Photos of claw mounts for MS rifles. [Re: Kiwi_bloke]
#158271 - 05/04/10 07:16 PM

Here's the claw mount on my FN-Browning 9,3x74R double rifle.

--------------------
André
---------------------------------
3 shots do not make a group, they show a point of aim or impact.
5 shots are a group.

Edited by CptCurl (16/04/10 08:07 PM)

Post Extras:

Pages: 1

Extra information

1 registered and 60 anonymous users are browsing this forum.

Moderator: CptCurl

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 4838

Jump to

NitroExpress.com

Home | Ezine | Forums | Links | Contact