Home | Ezine | Forums | Links | Contact
NitroExpress.com: Chamber resleeve advise needed

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies


*** Enjoy NitroExpress.com? Participate and join in. ***
You are not logged in. [Login] Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Double Rifles, Single Shots & Combinations >> Single Shots & Combination Guns
Previous topic Previous   View all topics Index   Next topic Next   Threaded Mode Threaded  

Pages: 1
Hendo
.224 member


Reged: 23/05/18
Posts: 44
Loc: South Australia
Chamber resleeve advise needed
      #341442 - 28/05/20 02:57 PM

Hi All, I have recently acquired an interesting little single shot, falling block action rifle chambered for .300 rook.
It has Belgium proof marks and has been reblued at some stage in its busy life. Unfortunately, the over enthusiastic polishing has left no hint of who the manufacturer is, (the proof marks are under the forearm, the only part of the octagonal barrel that's been left alone).

It looks like a previous owner has run out of Rook ammo and used something very much shorter (32 Colt??) because the chamber is badly eroded about halfway down , making it very difficult to eject a spent case.
My choices are either (1) resleeve the whole thing to 32-20 or more likely 25-25, a very costly exercise. or (2) find a gunsmith in Australia who can resleeve the chamber in the original cartridge chambering. This is preferred because , apart from a small patch of corrosion, the rifling looks quite good. and half the fun of these old workhorses is shooting them as they were originally.
So my question, Does anyone know of or can recommend a gunsmith in Australia who does this sort of work ie resleeving chambers

--------------------
.

Post Extras: Print Post   Remind Me!   Notify Moderator  
Hendo
.224 member


Reged: 23/05/18
Posts: 44
Loc: South Australia
Re: Chamber resleeve advise needed [Re: Hendo]
      #341443 - 28/05/20 03:31 PM

[image]https://imgur.com/CeyVQHV[/image]

--------------------
.

Post Extras: Print Post   Remind Me!   Notify Moderator  
Hendo
.224 member


Reged: 23/05/18
Posts: 44
Loc: South Australia
Re: Chamber resleeve advise needed [Re: Hendo]
      #341444 - 28/05/20 03:33 PM

Sorry folks, Haven't quite got the photo process sorted out but I am determined to.

--------------------
.

Post Extras: Print Post   Remind Me!   Notify Moderator  
93x64mm
.416 member


Reged: 07/12/11
Posts: 4198
Loc: Nth QLD Australia
Re: Chamber resleeve advise needed [Re: Hendo]
      #341450 - 28/05/20 10:33 PM

Yes you can get brass & dies
Follow the links
https://www.northernshooterssupplies.com.au/300-Rook-Unprimed-Brass-Cases-p/300rk.htm

I have to agree with you there Hendo - what would be your load?
Also it is a .300" projectile - casting will be in order, or will you resize .32-20 pills?

Post Extras: Print Post   Remind Me!   Notify Moderator  
DoubleD
.400 member


Reged: 23/11/03
Posts: 2437
Loc: Retired in Oklahoma
Re: Chamber resleeve advise needed [Re: 93x64mm]
      #341452 - 29/05/20 01:33 AM

https://i.imgur.com/CeyVQHV.jpg

How's this.



I had to resize your image as it was far to large to be seen properly on the board.

While from a collector stand point keeping this all original would be preferred, from a shooters view, relining would be the better way to go.

I doubt you will be able find a gunsmith with .300 reamer. The gun would better serve being relined. I don't think you will find much difference in cost to fully reline to 32-20 than just sleeving the chamber.

If you can sort the .300 reamer out, you still have to deal with finding brass dies and bullets which are not common-in an uncommon bore size.

--------------------
DD, Ret.

Post Extras: Print Post   Remind Me!   Notify Moderator  
lancaster
.470 member


Reged: 06/05/08
Posts: 9033
Loc: There's a lighthouse in the mi...
Re: Chamber resleeve advise needed [Re: DoubleD]
      #341456 - 29/05/20 03:37 AM

my point of view: the 300 rook is not a high power cartridge



what would I do? turning the barrel out of the receiver, looking for a lathe with a four-jaw chuck for the octagonal barrel. I would drill the chamber area out, maybe to 10 mm diameter. than soft solder a short liner tube - 10 mm outside, 8 mm inside into the chamber.

looking for a reamer

there are simple 8,1 mm reamer for sale in germany,not expensive
just ream a cylindrical chamber with such a tool.

--------------------
Norwegian hunter misses moose, shoots man on toilet
.
bringing civilisation to the barbarians

Post Extras: Print Post   Remind Me!   Notify Moderator  
HuviusModerator
.416 member


Reged: 04/11/07
Posts: 3555
Loc: Colorado
Re: Chamber resleeve advise needed [Re: lancaster]
      #341458 - 29/05/20 09:16 AM

Since your rifle has a very nice bore, I would try rechambering to 25/20 with a reamer pilot sized to the bore.
You would end up with a cleaned up chamber for a slightly bottle necked cartridge with a neck length of .235" if I'm thinking correctly.
That is if your existing neck area of the chamber is in good condition - you say the roughness is about halfway down the chamber.
Would be a 30-20 or if in keeping with the British way, maybe call it a 300 #2 Rook

--------------------
He who lives in the past is doomed to enjoy it.

Post Extras: Print Post   Remind Me!   Notify Moderator  
500Boswell
.400 member


Reged: 21/07/06
Posts: 1276
Loc: Queensland
Re: Chamber resleeve advise needed [Re: Huvius]
      #341488 - 30/05/20 08:04 AM

Alan Swan re sleeved a Low Wall for me in 32-20 ,was good !

Post Extras: Print Post   Remind Me!   Notify Moderator  
Pages: 1


Previous topic Previous   View all topics Index   Next topic Next   Threaded Mode Threaded  

Extra information
0 registered and 499 anonymous users are browsing this forum.

Moderator:  Huvius 

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 2934

Rate this topic

Jump to

Contact Us NitroExpress.com

Powered by UBB.threads™ 6.5.5


Home | Ezine | Forums | Links | Contact


Copyright 2003 to 2011 - all rights reserved