Home | Ezine | Forums | Links | Contact
NitroExpress.com: H&R slug master misfire

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies


*** Enjoy NitroExpress.com? Participate and join in. ***
You are not logged in. [Login] Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Double Rifles, Single Shots & Combinations >> Paradox and Bore Guns
Previous topic Previous   View all topics Index   Next topic Next   Threaded Mode Threaded  

Pages: 1
matthew69
.224 member


Reged: 27/05/12
Posts: 35
Loc: tasmaina australia
H&R slug master misfire
      #225775 - 22/02/13 04:21 PM

Hi

i took my slug master out for a shot last week and it would not fire just put little dents in the primer.
the same loads as the last time i used it with no misfire i have been reading on the net that the
transfer bar is a bit crud and will cause misfire.h&r has a new one to replace the old one so i got my gun shop looking into this for me .

has any one else had this happen to them and if so how did you fix it

thanks
matthew

Edited by matthew69 (22/02/13 04:22 PM)

Post Extras: Print Post   Remind Me!   Notify Moderator  
jaz
.300 member


Reged: 21/10/05
Posts: 188
Loc: Northeast US
Re: H&R slug master misfire [Re: matthew69]
      #225829 - 23/02/13 01:19 PM

I had the biggest buck I ever saw in front of me at 80 yards. Slowly I brought up the gun and pulled the trigger.... made a little dent in the primer. Cried for a week and had always attributed it to Federal ammunition, then switching to Hornady. Interesting

Post Extras: Print Post   Remind Me!   Notify Moderator  
hubel458
.375 member


Reged: 13/02/04
Posts: 649
Loc: Brinton,MI-USA
Re: H&R slug master misfire [Re: jaz]
      #226497 - 06/03/13 12:52 PM

As with most shotguns NEFs have generous headspace.
So I check the firing protrusion on all NEF guns I have
as well as all other guns of any kind. Some NEFs only protrude about .040"
and all shotguns need .060" at least.So on NEF I file off
back of breech stop so that hammer pushes the transfer bar
further forward shoving pin out further.

Also guns that have a light primer dent with some cases
I have, will indent better with Hornady cases as I measured them
with about .005" extra rim thickness. But you don't want to
put up with short firing pin protrusion when it can be fixed.Ed

--------------------
Ed Hubel

Post Extras: Print Post   Remind Me!   Notify Moderator  
fourbore
.275 member


Reged: 28/03/10
Posts: 70
Loc: NewEngland
Re: H&R slug master misfire [Re: hubel458]
      #226563 - 08/03/13 12:17 AM

A friend has this same problem and he replaced the firing pin. He did it himself and said it was a real tough job. he is not a gunsmith, just average guy. From what he said, sounds like he had heard of it also happen to another friend. So; while not common, it apparently does happen that the firing pin is just to short? I could give him a call and ask, that is the general idea what he told me.

Actually, it could be the chamber as stated above, but a workable fix was a new firing pin. I think his was a cf rifle.

now, NEF is part of Remington and I guess service really stinks. But, his gun was not from Remington anyway, as far as I know. The Remington/NEF had other problems, like scope rail popping off. And they dont like to talk on the telephone. probably not about to service the NEF guns. And if they did it could take months. Your are from Australia, so maybe not relevant I live just down from the old NEF (H&R) factory. You could walk right in the door and ask them to build a gun.

Hope this helps, ... If I see him, I will ask again. I dont think it was the transfer bar. Now, I wish I payed better attention.

Post Extras: Print Post   Remind Me!   Notify Moderator  
matthew69
.224 member


Reged: 27/05/12
Posts: 35
Loc: tasmaina australia
Re: H&R slug master misfire [Re: fourbore]
      #226581 - 08/03/13 05:44 AM

Thanks
This is helping heps going to take all info and h&r out to gun smith and hope he can get it going

Thanks Matthew

Post Extras: Print Post   Remind Me!   Notify Moderator  
hubel458
.375 member


Reged: 13/02/04
Posts: 649
Loc: Brinton,MI-USA
Re: H&R slug master misfire [Re: matthew69]
      #226616 - 08/03/13 01:55 PM

Sometimes new pin I've gotten is like old pin; IE same length.
Only fiddled around like that twice. And only easy fix, file back of
breech to get enough protrusion.Ed

--------------------
Ed Hubel

Post Extras: Print Post   Remind Me!   Notify Moderator  
fourbore
.275 member


Reged: 28/03/10
Posts: 70
Loc: NewEngland
Re: H&R slug master misfire [Re: hubel458]
      #226630 - 08/03/13 11:00 PM

I need to make a correction, was told the repair was a new main spring. Guess, I just not paying attention.

Post Extras: Print Post   Remind Me!   Notify Moderator  
Pages: 1


Previous topic Previous   View all topics Index   Next topic Next   Threaded Mode Threaded  

Extra information
0 registered and 14 anonymous users are browsing this forum.

Moderator:  tinker 

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 4112

Rate this topic

Jump to

Contact Us NitroExpress.com

Powered by UBB.threads™ 6.5.5


Home | Ezine | Forums | Links | Contact


Copyright 2003 to 2011 - all rights reserved