Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: D. rifle builders: What do you use for rib material?

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Double Rifles, Single Shots & Combinations >> Building Double Rifles & Gunsmithing

Pages: 1

doubleriflejack
.333 member

Reged: 11/11/07
Posts: 352
Loc: Oregon, U.S.A.

D. rifle builders: What do you use for rib material?
#101934 - 08/04/08 02:49 AM

Double Rifle builders: What do you use for rib material; where do you get it? Sometimes the ribs taken off shotgun can be used, but most of the time it is too narrow. I need a source for good ribs for double rifles, of proper width.

Post Extras:

szihn
.400 member

Reged: 24/06/07
Posts: 2121
Loc: United States

Re: D. rifle builders: What do you use for rib material? [Re: doubleriflejack]
#101952 - 08/04/08 09:13 AM

I use 1/32" X 1/2" Strap. Just 1028 hot rolled. You get it at any steel seller.

To make the concave form just take a piece of 3/4" round stock and use it as a press, and hammer the strap into a round mill cut in a 6" long piece of steel. Make the cut with a 3/4" or 7/8" ball end mill. The rib will not look perfect, but you need to fit it anyway, so it's tight to the barrels. When it's soldered up nicely at the edges, take a large rat-tail file to smooth out the bumps, and then a piece of 120 grit Wet-or-Dry over a 3/4" dowel, to make it all pretty.
It's a lot of hand work, but not really very hard to do. If you just take your time and it comes out beautiful.

Steve

Post Extras:

RSFknives
.300 member

Reged: 02/05/07
Posts: 232
Loc: Sweden

Re: D. rifle builders: What do you use for rib material? [Re: szihn]
#101993 - 08/04/08 11:49 PM

why not get some stuff from the italians... www.effebisnc.it
they make everything from barrels to mounts, ribs and recoil pads.

and then you have BFIM (also italy)
www.bfim.it

/Roger

--------------------
life is to short to own an ugly gun.

http://www.knifeguild.se

Edited by RSFknives (08/04/08 11:53 PM)

Post Extras:

Ron_Vella
.333 member

Reged: 29/04/05
Posts: 432
Loc: Oshawa, Ontario, Canada

Re: D. rifle builders: What do you use for rib material? [Re: RSFknives]
#102087 - 10/04/08 05:30 AM

For the last two double rifles that I've built, I bought both the top and bottom ribs from Tom Ondrus at Crown Press. The price was fair, the service was prompt and the quality of the product was good. The top ribs, particularly the area of the express sight base, needed some additional configuring in order to satisfy my sense of aesthetics but I was pleased with what I received from Tom and I am certainly pleased with the end result.

Edited by ronvella (10/04/08 05:31 AM)

Post Extras:

Marrakai
.416 member

Reged: 09/01/03
Posts: 3591
Loc: Darwin, Top End of Australia

Re: D. rifle builders: What do you use for rib material? [Re: Ron_Vella]
#102095 - 10/04/08 07:43 AM

Concave bottom ribs are easily made by cutting a sliver out of a length of appropriately-sized steel tube.

No bumps to smooth-out, Steve.

--------------------
Marrakai
When the bull drops, the bullshit stops!
--------------------------------
www.marrakai-adventure.com.au

Post Extras:

szihn
.400 member

Reged: 24/06/07
Posts: 2121
Loc: United States

Re: D. rifle builders: What do you use for rib material? [Re: Marrakai]
#102097 - 10/04/08 07:54 AM

That's a good idea.
What are you using to cut them out?

Post Extras:

RSFknives
.300 member

Reged: 02/05/07
Posts: 232
Loc: Sweden

Re: D. rifle builders: What do you use for rib material? [Re: szihn]
#102111 - 10/04/08 02:32 PM

Ronvella, does crown press have a website?

/Roger

--------------------
life is to short to own an ugly gun.

http://www.knifeguild.se

Post Extras:

Ron_Vella
.333 member

Reged: 29/04/05
Posts: 432
Loc: Oshawa, Ontario, Canada

Re: D. rifle builders: What do you use for rib material? [Re: RSFknives]
#102157 - 11/04/08 05:21 AM

Sorry for the delay, here is the contact information:

Tom Ondrus, C/O Crown Press,
P.O. Box 126,
Austinburg,
Ohio 44010, USA.
Phone: 440-275-1400
Fax: 440-275-1511
e-mail: [Email]crownpress@alltel.net.[/Email]

This info is about two years old so please do not fault me for any errors or ommissions. For a couple of dollars, Tom will send you photo-copies of his catalogue. It's worth your while since he has some useful and interesting trinkets for the tinkerer!

PS: He usually has some interesting, used double guns and rifles for sale as well.

Edited by ronvella (11/04/08 05:23 AM)

Post Extras:

BlainSmipy
.375 member

Reged: 24/11/05
Posts: 558
Loc: Washington, USA

Re: D. rifle builders: What do you use for rib material? [Re: Ron_Vella]
#102573 - 16/04/08 07:42 AM

I've tried Toms (He's a great guy BTW) stuff its good, I also have steel strips, 1/4", 3/8", 1/2" and 3/4". Quarter ribs are made from 3/8" square stock milled and ground to shape...mostly by hand.

I am however, engaging a CNC milling company to make complete top ribs with quarter rib as an experiment.

bs

--------------------
You horde gold, I horde lead.

Post Extras:

Pages: 1

Extra information

0 registered and 24 anonymous users are browsing this forum.

Moderator: CptCurl

Print Topic

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Topic views: 605

Jump to

NitroExpress.com

Home | Ezine | Forums | Links | Contact