The U.S. Model 1855 Pistol Carbine
by JOHN D. MCAULAY posted on June 28, 2021

https://www.americanrifleman.org/content/the-u-s-model-1855-pistol-carbine/

In 1855, the U.S. Army adopted the Maynard tape primer system and the .58-cal., hollow-base Minié ball as standard features on its new small arms, including the muzzleloading .58-cal. Model 1855 Pistol Carbine. While produced only in small quantities, the M1855 nonetheless remained in limited service for nearly a decade.

U.S. Model 1855 PistolChief of Ordnance Col. Henry K. Craig reported to Secretary of War Jefferson Davis on June 26, 1855, on the ordnance board recommendations regarding the establishment of new arms for military service. In reference to the carbine, Craig stated, “.58 inch is proposed for all small arms … 10 inch for the barrel of the pistol, which barrel, being also provided with a suitable stock, will answer for a dragoon or artillery carbine, for which a range of 500 yards fits it … a small lock, with magazine for 25 primers, will serve for either the pistol or artillery carbine … .”

Davis approved the recommendations on July 5, 1855, and wrote: “the pistol will be provided with a movable stock, by the application of which, it may be used as a carbine by light artillery and mounted troops.” Further testing concluded that accuracy, as well as the energy generated, increased with the length of the barrel. On Aug. 23, 1855, the recommendation was made to increase the length of the barrel from 10" to 12".

The .58-cal. M1855 Pistol Carbine’s overall length with its attachable shoulder stock was 281/4", and it weighed 5 lbs., 7 ozs. The pistol alone was 173/4"-long and weighed 3 lbs., 13 ozs. The shoulder stock and the pistol’s stock were both oil-finished, black walnut. The lock was fitted with a Maynard tape primer magazine holding 25 pellet primers in its tape. The primer door was stamped with a large spread eagle, and forward of the door is stamped “U.S./SPRINGFIELD” on two lines. To the rear of the C-shaped hammer was the date, either 1855 or 1856. The bright 12" barrel had an iron blade front sight and a two-leaf rear sight graduated to 400 yds. The nipple bolster was equipped with a clean-out screw. The upper left flat was stamped with the proofmarks “V/P” and an eagle head, and the date was marked on the top barrel flat near the breech. The barrel was held by a single flat brass band with a sling swivel mounted on it. The barrel band was retained by a conventional spring forward of it. The ramrod swivel lug was brazed to the bottom of the barrel, while the button-head ramrod was held in place by a double-arm swivel. A lanyard ring was mounted on the buttcap, while the toe of the attachable stock was equipped with a sling swivel. Batch numbers from 1 through 25 are found on the backstrap of the pistol and the brass yoke of the shoulder stock. The tang of the buttplate is stamped “U.S.”

Maynard’s tape primer system was patented in September 1845 by Dr. Edward Maynard, a Baltimore dentist. Its purpose was to eliminate the need to manually place a percussion cap on the nipple each time the pistol was fired. A paper roll carrying the priming compound was advanced over the nipple each time the hammer was cocked; the system is similar to what is used by many toy “cap” guns. However, the pistol could still be fired with conventional percussion caps. The cartridge finally settled on for the M1855 Pistol Carbine had a .577"-diameter Minié-style elongated ball with a bullet weight of 450 grs., a blackpowder charge of 40 grs. and an overall length of 1.9".

Production on the M1855 began in the fall of 1855. By the end of June 1856, Harpers Ferry Armory had fabricated three pistol carbines and Springfield Armory had manufactured 1,003 pistol carbines. Between late 1855 and June 30, 1857, 4,019 M1855 Pistol Carbines were manufactured at Springfield Armory, plus the three at Harpers Ferry.

Continued: