Forums.NitroExpress.com

Home | Ezine | Forums | Links | Contact NitroExpress.com: 16 Bore Husky Model 17?

View recent messages : 24 hours | 48 hours | 7 days | 14 days | 30 days | 60 days | More Smilies

*** Enjoy NitroExpress.com? Participate and join in. ***

You are not logged in. [Login]

Main Index · Search · Active Topics
New user · Who's Online · FAQ · Calendar

Double Rifles, Single Shots & Combinations >> Paradox and Bore Guns

DarylS
.700 member

Reged: 10/08/05
Posts: 26645
Loc: Beautiful British Columbia, Ca...

16 Bore Husky Model 17?
20/01/09 06:57 AM

Finally got around to shooting the 16 bore with balls. I used .684" pure lead balls that I cast for the 14 bore cap-lock rifle. They engrave about 1/2 depth of the straight rifling. The target was shot offhand (standing) at 28 yards at a light spot on a piece of cardboard found on the range. I had to walk in and since it was a test, I didn't pack my shooting box with real targets, stapler, etc. The first 5 shots went into a group about 1 1/2", but the next 5 shots opened the group to over double, if you cound the low left shot. That shot, #6 could have been a bad hold, but felt good. I'm not sure it's mine, really, but stranger things have happened. I think if held tightly and shot off the bench, I could have made a pattern under 2" with 10 shots. This was the first time this gun has fired since I got it, shown by the 'rough' first test. The next test will be a bit more comprehensive, if I can get proper wads. I think the 480gr. wall will suffice. This gun shot to the sights, holding the bead just 1/8" higher than the bottom of the wide V. It looked and felt good, so I was happy to see the impacts just over the bead. If anything, it shot a bit left for the first run of 5 rounds. After heating up, the group moved a tich right - might have been me. I was cold, tired and not shooting 'up to snuff'.

The load used was a .715" hard card 1/8" over 82gr. 3F GOEX, then 2, 1/2" 16 bore lubed fibre wads(undersize), then the .684" ball, then crimping using the 12 bore paper crimping cone from my Herter's loading press. When cleaning, there was no leading - I was surprised and happy overall. I'll edit to include more pictures. I'll try to get some 13 bore wads for further testing.

Post Extras

Print Post

Remind Me!

Notify Moderator

Entire topic
Subject	Posted by	Posted on
16 Bore Husky Model 17?	DarylS	20/01/09 06:57 AM
Re: 16 Bore Husky Model 17?	rigbymauser	20/01/09 07:34 AM
Re: 16 Bore Husky Model 17?	Der_Jaeger	20/01/09 07:56 AM
Re: 16 Bore Husky Model 17?	DarylS	26/01/09 07:37 AM
Re: 16 Bore Husky Model 17?	DarylS	09/03/09 05:39 AM
Re: 16 Bore Husky Model 17?	lancaster	09/03/09 06:39 PM
Re: 16 Bore Husky Model 17?	lancaster	09/03/09 10:40 PM
Re: 16 Bore Husky Model 17?	DarylS	10/03/09 01:09 AM
Re: 16 Bore Husky Model 17?	DarylS	12/03/09 04:25 AM
Re: 16 Bore Husky Model 17?	DarylS	09/07/09 05:11 AM
Re: 16 Bore Husky Model 17?	450_366	09/07/09 07:44 AM
Re: 16 Bore Husky Model 17?	DarylS	10/07/09 12:04 AM
Re: 16 Bore Husky Model 17?	beleg2	20/01/09 08:26 AM
Re: 16 Bore Husky Model 17?	88MauSporter	20/01/09 08:38 AM
Re: 16 Bore Husky Model 17?	DarylS	20/01/09 10:20 AM
Re: 16 Bore Husky Model 17?	bonanza	20/01/09 10:28 AM
Re: 16 Bore Husky Model 17?	Omnivorous_Bob	20/01/09 03:08 PM
Re: 16 Bore Husky Model 17?	lancaster	20/01/09 07:41 PM
Re: 16 Bore Husky Model 17?	DarylS	21/01/09 07:46 AM
Re: 16 Bore Husky Model 17?	lancaster	21/01/09 05:57 PM
Re: 16 Bore Husky Model 17?	450_366	21/01/09 08:30 AM
Re: 16 Bore Husky Model 17?	DarylS	21/01/09 11:53 AM
Re: 16 Bore Husky Model 17?	rigbymauser	21/01/09 08:02 PM
Re: 16 Bore Husky Model 17?	DarylS	22/01/09 03:43 AM
Re: 16 Bore Husky Model 17?	450_366	22/01/09 05:15 AM
Re: 16 Bore Husky Model 17?	88MauSporter	23/01/09 02:34 PM
Re: 16 Bore Husky Model 17?	lancaster	24/01/09 12:25 AM
Re: 16 Bore Husky Model 17?	DarylS	24/01/09 04:03 AM

Extra information

0 registered and 7 anonymous users are browsing this forum.

Moderator: tinker

Forum Permissions
      You cannot start new topics
      You cannot reply to topics
      HTML is disabled
      UBBCode is enabled

Rating:
Thread views: 11327

Jump to

NitroExpress.com

Powered by UBB.threads™ 6.5.5

Home | Ezine | Forums | Links | Contact

Copyright 2003 to 2011 - all rights reserved